ParisMobile hydraulic lifting platformHow to do daily maintenance and maintenance

The load capacity of goods and the tonnage of goods transported at once also affect the speed of lifting and lowering. Achieving the excellent value of the lifting platform for transporting goods is a guarantee of speed. If the weight is too heavy it affects the speed. If the goods are too light, it also affects the normal transportation time.When conducting high-altitude operations on dangerous edges such as roofs, suspension bridges, slopes, or cliffs, guardrails or safety nets should be installed on the side facing the air, or safety belts or ropes should be used.Paris,Before use, carefully check the grounding wire, safety devices, buffer springs, etc. Ensure a safe usage environment.What are the advantages of installing a guide rail type elevator for goods? The advantages of civil engineering are easy to install: there is no need for a machine room above the shaft, and the top layer can be installed at a height of more than meters. The computer room can be located within a radius of meters of the shaft, occupying an area of only - square meters. The hydraulic elevator is not equipped with a counterweight device to improve the utilization rate of the shaft area. The load and load cylinder of the hydraulic elevator directly act on the foundation pit and the strength requirement for the shaft is low. A brick structure or brick concrete structure shaft is sufficient.Panalanoy,Check the hydraulic oil quality and level. When the lifting platform is raised to a high position, the hydraulic oil level should be - millimeters higher than the bottom of the oil tank. When the color of the hydraulic oil darkens, the oil becomes sticky, or there are foreign objects such as gravel in the oil, the hydraulic oil should be replaced in a timely manner. The hydraulic system of the lifting platform should be checked for hydraulic and pipeline connections. If the pipeline is damaged, it should be replaced immediately; When there is looseness in the connection part, tighten the pipe joint.High altitude work requires the use of tool bags, and heavier and larger high-altitude work tools should be hung on stable components and cannot be placed randomly to avoid the occurrence of high-altitude falling accidents.The size of the oil cylinder should be minimized as much as possible while meeting the design requirements. The smaller the size of the oil cylinder, the faster the lifting speed.

Guide rail type cargo elevators are a type of equipment for transporting heavy objects up and down,ParisDouble shear hydraulic lifting platform, and have great applications in factories workshops, and other places. For this type of heavy machinery, its daily maintenance and upkeep are very important, because some small details can have a significant impact on the operation safety of the equipment if not paid attention to. Therefore, attention should be paid to the daily maintenance of cargo elevators.How should we extend the service life of hydraulic lifting platforms? In order to prolong the service life of such machinery and equipment, if there are various switch devices inside the machinery and equipment, it is necessary to regularly check whether these switches can be used normally and whether the switch points are in good condition during use. There will be an electrical box and distribution box inside the elevator, and these devices are prone to dust accumulation outside. If the dust accumulates too much, when using them, it is necessary to regularly remove the dust on the outside of various boxes. Generally, this job is what operators should do after each operation.Check the rollers, and bearings; Oil cylinder pin and bearing; Equality and wear of the hinge shaft and bearings of the boom; Add oil to the above components for maintenance of outdoor elevators and factory elevators. Extend the service life of bearings.How much is it,Loosening: The newly processed and assembled components of high-altitude work platform equipment such as mobile elevators have a tendency to have geometric shapes and matching dimensions. In the early stages of equipment use, due to the influence of alternating loads such as impact and vibration, or factors such as heat and deformation, coupled with rapid wear and tear, it is easy to cause the previously fastened components of high-altitude work platform equipment such as mobile elevators to become loose.For the safety performance of high-altitude work platforms, it is necessary to have production technology, scientific processes, and strict management to ensure production. When in use, people,ParisManual hydraulic lifting platform, the environment, and machines are the three major links of high-altitude operations, and safety is the basic condition to ensure the smooth progress of high-altitude operations. In the following text, Jiuyi briefly describes the precautions for using high-altitude operation platforms: high-altitude operators must hold a health certificate. Individuals with mental illness, hypertension, and the oil inlet filter is blocked; The fuel supply pump has drawbacks; Check the wear and tear of the one-way valve core and valve seat, and check if the one-way valve spring is tired or deformed.

Good stability: The overflow valve can prevent excessive system pressure during upward movement. Emergency manual valve: In case of power failure, it can cause the elevator car to descend to the nearest floor position and open the door. Manual pump: When the system malfunctions, the manual pump can be operated to pump high-pressure oil to raise the car to the nearest floor position; Tank oil temperature protection: When the oil temperature in the tank exceeds the standard setting value, the oil temperature protection device sends a signal to suspend the use of the elevator. The elevator can only be started when the oil temperature drops.Quality inspection report,What are the advantages of installing a guide rail type elevator for goods? The advantages of civil engineering are easy to install: there is no need for a machine room above the shaft, and the top layer can be installed at a height of more than meters. The computer room can be located within a radius of meters of the shaft, occupying an area of only - square meters. The hydraulic elevator is not equipped with a counterweight device to improve the utilization rate of the shaft area. The load and load cylinder of the hydraulic elevator directly act on the foundation pit, and the strength requirement for the shaft is low. A brick structure or brick concrete structure shaft is sufficient.Timely wrapping and replacement of damaged parts is a type of hydraulic elevator, also known as guide rail hydraulic elevator, restaurants, and hotel floors. Here is Lipusheng Machinery to introduce the daily maintenance of the elevator.The explanation mainly focuses on the mechanism of lifting platforms, and now there are many different types of lifting platforms. In order to better use lifting platforms, we have started to develop different industries using different lifting platforms. Electric lifting platforms have become the main product of small lifting platforms. They are small in size, light in weight, practical in appearance, easy to move, large in load capacity, and large in plane area, Stability has become a machinery that many customers are competing for, and lifting equipment is used in enterprises of all sizes, so the use of lifting platforms is necessary.Paris,With the increasing demand for boarding bridges, mobile boarding bridge merchants are increasingly interested in using boarding bridges to provide customers with the appearance of hydraulic boarding bridges, and the demand for boarding bridges is also increasing. However, there are not many manufacturers of corresponding boarding bridges. Many boarding bridge companies are leather bag companies, and they do not produce them themselves, resulting in high prices. What is important is that they do not have a good understanding of the technology of car booths, and there are often deviations when passing on the technical requirements of direct customers to the manufacturers. Therefore, customers who purchase boarding bridges can directly find professional manufacturers. When choosing a boarding bridge, the first thing to consider is the range of use, frequency of work, utilization, rated weight, and other factors of the product, and choose a boarding bridge that is suitable for the requirements of the unit. Conduct market research based on the proposed technical parameters. The first condition for selecting a supplier is to consider the manufacturer of the boarding axle, and then the after-sales service capability. As long as it is a fixed boarding bridge with good product quality, excellent performance, and complete equipment, it can be chosen at a reasonable price.What are the advantages of installing a guide rail type elevator for goods? The advantages of civil engineering are easy to install: there is no need for a machine room above the shaft and the top layer can be installed at a height of more than meters. The computer room can be located within a radius of meters of the shaft, and the strength requirement for the shaft is low. A brick structure or brick concrete structure shaft is sufficient.High altitude work requires the use of tool bags occupying an area of only - square meters. The hydraulic elevator is not equipped with a counterweight device to improve the utilization rate of the shaft area. The load and load cylinder of the hydraulic elevator directly act on the foundation pit, and heavier and larger high-altitude work tools should be hung on stable components and cannot be placed randomly to avoid the occurrence of high-altitude falling accidents.