ValpalotaSingle rail lifting platformTalking about the absorption of rays

Attention: Abnormal meshing of gear teeth should be avoided: uneven rolling of the rollers should be avoided; Avoid diagonal orientation of the guide rollers; It should be avoided that the guide rollers are kept at the same time for a long time; The above abnormal phenomena can lead to rapid wear and even scrapping of gears, racks, rollers, and guide rails. If adjusted more carefully, and carefully inspect the steel structure, safety protection devices, electrical devices, and transmission devices of construction elevatorsValpalota,Applicable environment: Indoor or outdoor Applicable temperature: Safety device Safety rocker: When the equipment is running and rising, the rocker will automatically prevent wheelchair platform.Manganese steel is generally used as the primary profile for warehouse cargo elevators. In order to achieve better anti-corrosion effect, a layer of rust resistant primer is usually applied, which effectively blocks air and prevents premature corrosion of the steel. Below, Ruilong hydraulic press will explain the role of rust resistant primer.Karlovo,Check the fastening status of the wall bracket, support rod, and bolts and retaining rings between the lifting cargo elevator and the bridge. If they are loose or displaced they should be checked and tightenedClean and inspect the crown wheel frame assembly, correct or replace with new partsMany times, after installing hydraulic cargo elevators in factories, floors, docks, and other places, there may be some adverse reactions and problems in the early stage. Below, Yakali's editor summarizes some common problems with hydraulic cargo elevators and provides some statements on how to solve and prevent these problems.

　　?? Hidden danger investigation relies on joint efforts from all aspects:?? Construction enterprises are the main responsibility for identifying hidden dangers in construction elevators. They should strengthen daily inspections and regular inspections, and carefully inspect the steel structure, safety protection devices, electrical devices, and transmission devices of construction elevatorsHeavy load capacity: protective plate form: ° Or ° Interchangeable configuration rocker working angle: ° Drive method: hydraulic power unit drive or screw drive.Adjust and correct various safety doors and mechanical interlocking equipmentProduction department,After cleaning, clean the filter and replace it with a new filter element before adding new oil. What adverse reactions may occur during the early use of hydraulic cargo elevators?Check the smooth steel wire rope and various fasteners, if there is excessive wear, it is necessary to replace themCheck and clean the driving gears and guide wheels of the elevator. If there is excessive wear, it is necessary to replace them

Lifting and loweringbuild,Check the wear condition of the pinion and rack, please refer to the instruction manual for specific requirementsThe vibration frequency should be set to obtain large dynamic stress with low energy consumption, and the resonance frequency should be used to handle time dependent vibration. However,ValpalotaLarge fixed lifting platform, there may be one or more resonance peaks in large components, which slowly increases the speed of the excitation motor from ,ValpalotaScissor fork lifting platform movement, and determines the relationship curve between the amplitude of the workpiece and the motor speed to determine the resonance point of the workpiece. According to the scanning curve,ValpalotaMobile boarding bridge, a large acceleration was obtained at r/min, so r/min was determined as the aging frequency.When disassembling the hydraulic oil tank filler cap, filter cover, inspection hole, it is necessary to avoid dust during the system oil passage. The disassembled parts must be thoroughly cleaned before opening. When disassembling the hydraulic oil tank filler cap, first remove the soil around the tank cap. After loosening the tank cap, remove any remaining debris from the joint area (do not rinse with water to prevent water from seeping into the tank). Only after confirming cleanliness can the tank cap be opened. When using materials and hammers, materials that do not remove fiber impurities and specialized hammers with rubber attached to the surface should be selected. Hydraulic components and hydraulic hoses should be carefully cleaned, dried with high-pressure air, and then assembled. Choose a well packaged filter element (the inner packaging is damaged, although the filter element is intact, it may also be unclean). When changing the oil, clean the filter at the same time. Before installing the filter element, carefully clean the bottom dirt inside the filter housing with materials.Valpalota,With the continuous development of the economy, meeting the needs of society, and increasing productivity hydraulic cargo elevators play an important role in high-altitude operations. Hydraulic cargo elevators operate up and down, up and down travel and can provide us with a safe and stable platform. We can provide security for our safety when working at heights.Check the interlocking equipment, and other safety maintenance switches of the cage door and fence doorWeekly maintenance: According to the operation instructions