HollingoleMobile boarding bridgeIntroduction to the organization and working principle of

Check all standard sections and diagonal support connection points. Check the fastening bolts of the gear rack and ensure that the motor cooling wing plate and organization are cleanThe reduction gearbox, gearbox, external meshing gear and other parts, as well as the hydraulic oil, are all carried out according to the requirements in the table.Hollingole,The driver shall close and lock the movable doors at both ends of the protective fence before work, and then ring the bell to start. It is strictly prohibited to work with the movable doors of the protective fence open. In case of special circumstances during platform operation, the emergency stop switch can be used to stop the platform. However, during normal operation, it is prohibited to use the emergency stop switch to stop the platform.The cleaning oil for the hydraulic system must use hydraulic oil of the same brand as the system used, with an oil temperature between and ℃. Use a large flow rate to remove impurities from the system as much as possible. The hydraulic system needs to be cleaned repeatedly three times or more. After each cleaning, fully drain the system while the oil is hot.San kolomad gramenet,Organize, and reinforce the severely corroded load-bearing membersA non scissor type hydraulic lifting mechanical equipment used for transporting goods between floors of industrial factories, restaurants, and restaurants on the second and third floors. Professional elevator manufacturers are safe, environmentally friendly, and economical! Our products are exported to foreign countries and highly trustedRegularly check whether the operation of each mechanism is normal and whether there is any noise. If any faults are found, they must be promptly eliminated.

Leakage occurs due to looseness, vibration, and the influence of heat on the sealing surface and pipe joints of the machine; Some casting, processing and other defects are difficult to detect during assembly and debugging, but due to vibration and impact during the operation process, these defects are exposed, manifested as oil (water) leakage. Therefore, leakage is prone to occur during the running-in period. Poor, due to the small fit clearance of newly assembled components and the difficulty in ensuring the uniformity of fit clearance due to assembly and other reasons, oil (grease) is not easy to form a uniform oil film on the friction surface to prevent wear. This reduces efficiency and causes early abnormal wear of the components. In severe cases,HollingoleAluminum alloy hydraulic lifting platform, it can cause scratches or bite on the friction surface of precision fitting leading to the occurrence of faults.Whether the vibration aging treatment has achieved the results can be judged based on the parameter curve observation method.Check the fastening status of the wall bracket, support rod, and bolts and retaining rings between the lifting cargo elevator and the bridge. If they are loose or displaced, they should be checked and tightenedCustomer first, correct or replace with new partsCheck and clean the driving gears and guide wheels of the elevator. If there is excessive wear, it is necessary to replace themBidding,Check the oil level of the gearbox and make up for new oil if necessaryWhen the lifting base plate descends, the safety net below immediately stops running and descends when encountering obstacles.Check the clearance of the ball bearing and the wear of the suspension wheel guide wheel. If the roller is worn, it is necessary to adjust or replace it. If the elevator bearing is worn, replace the guide wheel or bearingHollingole,The wear rate is fast, and due to factors such as processing assembly, and adjustment of new machine components, the friction surface is rough, the mating surface area is small, and the surface pressure condition is uneven. During the operation of the machine, the concave and convex parts on the surface of the parts are intertwined and rubbed against each other. The metal debris that falls off from the grinding process, in turn, acts as abrasive and continues to participate in friction, further accelerating the wear of the mating surface of the parts. Therefore, during the running-in period it is easy to cause wear on components (especially the mating surface), with a fast wear rate. At this point, if overloaded, it may cause damage to the components and lead to early failures.Transfer of goods between floors of rooms, restaurants, and restaurants. The low height is between -mm, especially suitable for workplaces that cannot excavate pits. And there is no need for upper lifting points, with diverse forms (single column, double column four column), stable equipment operation, simple and reliable operation, economic and convenient goods transmission, and difficult to solve narrow spaces that cannot reach the requirements. A customized delivery platform can be created, and the product hydraulic system is equipped with anti fall, upper and lower door interaction, and operation buttons can be set on each floor and lifting platform workbench to achieve multi-point. The product has a sturdy structure, a large load-bearing capacity, smooth lifting, making it an ideal and economical cargo conveying equipment for replacing elevators between low floors. The lifting stage device is mainly responsible for data processing of the operation mechanism and work bar of the vehicle, calculating the safety area of the lifting stage, and is suitable for the electric control system of the self lifting stage lifting platform. The main sensors in the electric control system include angle sensors, long angle sensors, dual axis inclination sensors, and energy saving of the oil cylinder system.Check the oil level of the gearbox and make up for new oil if necessary