SereniolaElevator enterpriseProduct performance and service life

Are the water cooling and air cooling of the hydraulic station the same?Avoid working in an environment. In the event of rain, snow and other weather, the use of the hydraulic lifting platform should be stopped to prevent the occurrence of a short circuit, resulting in electric leakage and electric shock; non-professionals are strictly prohibited from disassembling electrical appliances such as hydraulic lifting platforms. In the event of an accident, you can’t disassemble without permission to eliminate the cause. You must report to the manufacturer for repair in time, and the manufacturer will guide you to complete the inspection or send someone to repair it; do not disassemble the appliance without permission! Professional elevator factory guarantees quality, guarantees service. Guarantees quality. Your satisfaction is our pursuit! Welcome to inquire.Sereniola,Cleaning and keeping it clean is the first priority. Regularly clean up the dust or sundries on the motor of the hydraulic lifting platform, otherwise the long-term accumulated dust will fall into the motor fan, and it will be very difficult to run, just like the laptop we usually use. If the dust on the computer fan is not cleaned, the computer will not be easy to dissipate heat, or even buzz. It will be much better after cleaning, and the same is true for the motor of the hydraulic lifting platform. V or V; how to properly maintain the motor of the hydraulic lifting platform to avoid the motor, of course, do not use it outdoors in rainy and snowy weather, etc., and pay attention to the selection during storage The environment is clean and dry; it is strictly forbidden to overload the hydraulic lifting platform. When using the hydraulic lifting platform, it must not be overloaded, which will bring a burden to the motor, and it may burn out the motor; At this time, you may wish to consult the manufacturer about the overload protection device. The overload protection device is generally selected by the manufacturer. After adding this device, you don’t have to worry about whether it is overloaded during use. It is not too expensive to add this device. Safe, stop the machine in time and continue running after troubleshooting. The motor bearings must be in good condition.Otsu ,What kind of function can be achieved by installing the elevator? Before installation, confirm whether the motor and the elevator are intact, and strictly check whether the dimensions of the parts connected to the motor and the elevator match. Here are the dimensions of the positioning boss of the motor, the input shaft and the groove of the elevator. Fitting tolerances.The contact opening and closing of the travel switch of each safety device must be reliable, and the contact arc crater should be polished in time.In addition to the fixed mode,SereniolaElevating cargo elevator 1-4 floors, the elevator also has a vehicle-mounted mobile type. As the name implies, it combines the lifting equipment with the vehicle-mounted system. Such a lifting equipment is very flexible to move, and of course it is more useful. For example There is this kind of lifting equipment in the airport, and it is also possible to install this kind of equipment in stations or stadiums. Since it can be moved the scope of operation is not limited to a certain place, and it can be used wherever lifting operations are required. It can be used. For example, when installing outdoor advertisements, the height of some advertisements is relatively high. At this time, mobile lifting equipment can be used to send billboards or staff to the designated height to work. This kind of equipment can also be divided into two types according to the driving mode: hydraulic lifting and electric lifting. The so-called hydraulic lifting is driven by hydraulic oil to reach a specified height. The electric mode is driven by a motor or geared to lift to A certain height, but at present, hydraulic lifting platforms are more widely used.

Guide rail lift (also known as freight elevator) is a non-scissor hydraulic lifting platform, which is mainly used in industrial plants, restaurants, restaurants, docks, workshops and other places that need to move goods vertically between high-rise buildings above the second floor. The low height is especially suitable for sites where the site is not suitable for digging pits. What problems do we need to pay attention to in these places where elevators are used?After the inspection the elevator manufacturer reminds you to use a compressed air machine to dry all the electrical connection parts inside the head compartment, so as to avoid corrosion caused by moisture accumulation in the electrical connection parts.Hydraulic pump station: special pump station for domestic lifting platform, protection device outside the pump station imported from Italy: organ m type, mesh type, iron plate seal type.Quality Assurance,The last thing to note is that, compared with the lifting platforms in some places, protective fences are generally added on the platforms. Since the lifting platforms are special equipment, the National Quality Inspection Bureau is very strict on this piece of inspection. All must be dismantled, so when the personnel ask you if you want to add a guardrail, don't blindly refuse, and consider whether it is necessary according to the site of use. In addition,Sereniola3 ton lifting cargo elevator, you must have the 'People's Republic of Special Equipment Manufacturing License' and the 'People's Republic of Special Equipment Installation, Transformation and Maintenance License' to produce, install,SereniolaLifting cargo elevator 1 ton, and maintain. Therefore, you must ask whether the manufacturer has these two certificates.The motor connection is wrong. When the delta connection motor is wrongly connected into a star shape, the motor still runs with full load, and the current flowing through the stator winding will exceed the rated current, and even cause the motor to stop by itself. If it overheats it will burn out. When the star-connected motor is wrongly connected into a triangle, or the motor with several coil groups connected in series to form a branch circuit is connected in parallel with two branches, it will cause the winding and core to overheat, and in severe cases, the winding will be burned.Check the limit switch to see if all the limit switches are loose. If so, nuts, screws, etc. are loose, if any, should be reinforced immediately; ensure that the hydraulic lifting platform rises and falls smoothly; outriggers (for high-altitude operating platform)

The hydraulic lifting platform is mainly the pressure transmission of hydraulic oil to realize the lifting function. Its scissor mechanical structure makes the lift stable, and the wide operating platform and high carrying capacity make the high-altitude operation wide and suitable for many people work at the same time. It makes high-altitude operations efficient and secure.Where can I find it?,Conscientiously write the special construction plan for installation and construction, and make safety technical disclosures to the installers.The elevator incidents that occurred in China in recent years in mobile elevator manufacturers are caused by three factors, which is purely caused by the lack of equipment-related operators. The second type is simple lifts such as hoists that have been eliminated in China and are not allowed to be used. It is aging equipment human error, more prone to accidents. The third is that the quality of production is not good enough, leading to serious social security accidents.What are the maintenance rules for hydraulic lift machinery? The brakes of each mechanism should be checked frequently and the gap between the brake shoe and the brake wheel should be adjusted to ensure flexibility and reliability. There should be no dirt on the friction surface, and if there is dirt, it must be washed off with gasoline or thinner.Sereniola,The hydraulic lifting platform can be divided into: four-wheel mobile type, two-wheel traction type, car modified type, car type, auxiliary self-propelled type, and the lifting height ranges from a meter to s meter.Hydraulic pump station: special pump station for domestic lifting platform, protection device outside the pump station imported from Italy: organ m type mesh type, iron plate seal type.The cleanliness of the hydraulic station is an important aspect of the elevator hydraulic station, so it should not be careless. Moreover, from a professional point of view, there are relevant rules and requirements, and you should refer to the specification manual, so that you can have a correct understanding and know how to achieve better cleanliness.