Gann tikwaWater well pipeline pumpOperation warning instructions

　　The pump can often be selected according to the specific requirements of lift, flow and liquid delivery. The flow range of the delivered liquid is - L / s, the pressure range is .- MPa,Gann tikwaSelf priming slurry pump wholesale, and the diesel engine speed range is - rpm. Features: water pump, high automation and performance　　 The pump body (can not) bear the pressure from the outlet pipeline system. The standby pump in the warehouse should rotate (/ times a week to make the shaft bear the load and external vibration evenly. The belt CR drive is that the motor is on the (right) side of the pump from the inlet of the pump.Gann tikwa,　　 water temperature (maximum)　　Wheel, mixing impeller and other main flow passage parts are made of high wear-resistant raw materials, which are wear-resistant, corrosion-resistant non clogging, and can effectively pass through large solid particles. It is not limited by suction range, and the investment is lower.Ouani,　　Through the introduction, we learned that the submersible slurry pump can be used to transport slurry when it is used at ordinary times. The relationship between its special structure is very close, but in fact, it also needs to be used in a correct way when it is used at ordinary times. Only in this way can　　If the pressure in the local area is equal to or lower than the vaporization pressure corresponding to the water temperature in the flow process, the water will vaporize there and form many small bubbles mixed by steam and gas. The cavitation phenomenon is due to the bubble action when these small bubbles flow from the low-pressure area to the high-pressure area in the water pump, there is generally only outgoing cable, and the user needs to connect it separately during installation. If the connection is wrong,Gann tikwaIrrigation deep well pump, it will seriously affect the normal operation of the pump, so we should follow the correct steps to connect.

　　So it is called: submersible slurry pump.　　The waste water and dirt of conveying belt particles in factories, steel mills, power plants, coal processing industries, drainage systems of urban sewage treatment plants, municipal engineering, construction sites and other industries can also be used to pump clean water and corrosive media.　　Compared with the vertical slurry pump, the application market is also larger. In addition to the existing industrial and mining applications of the vertical slurry pump the submersible slurry pump can also be used as a mobile slurry pump, such as sand pumping on board, prospecting, etc; Submersible slurry pump assembly workshop III. what are the advantages of submersible slurry pumpaverage method,　　 Moreover, the processes of these two pumps are also different, and the sewage pump can generally be adjusted. Submersible pumps are generally used in some special or other places.　　 Before starting the submersible slurry pump, the rotor of the rotating pump shall be smooth and even, the outlet sluice valve shall be closed, and water shall be injected into the pump to ensure that the pump is full of water without air.　　The effective power is also called output power,Gann tikwaSewage pump diving, which is expressed by PE. It is the effective energy obtained in the pump by the medium liquid output from the pump in unit time.

　　When in use, it can drive the impeller to rotate so as to drive it to flow.reform,　　When this type of pump is used at ordinary times, the pump and motor operate in a coaxial whole. When it runs, the motor shaft will drive the impeller of the pump to rotate, and then at this time, the rotating force can be brought to the medium, so that　　Put it into water for use.　　After meters, the sealing of the equipment can not bear the water pressure at this depth.Gann tikwa,　　There is no need to equip auxiliary mixing or spraying equipment, and the operation is simpler. The equipment is directly submerged for operation, without noise and vibration, and the site is cleaner.　　For example, in the market, for example, it is not suitable to use a vertical slurry pump under such a working condition some of which have a depth of more than meters, but it is extremely easy to use a submersible slurry pump.　　 Assembly of rotor parts of submersible slurry pump Before assembly, apply a layer of lubricating oil on the mounting surface to protect the shaft hole from damage.