BelskbiavaHydraulic lifting platform frameIntroduction to the preparation work that needs to be done before homework

Regularly check all wires and cables for damage. It is necessary to wrap and replace the damaged parts in a timely manner.The hydraulic oil used in the system has the same brand, and the oil temperature is between ~ ℃. Use a large flow rate to remove impurities from the system as much as possible. The hydraulic system needs to be cleaned repeatedly three times or more, and after each cleaning, the system should be drained while the oil is hot. After cleaning, clean the filter and add new oil after using a new filter element.Belskbiava,It must be abnormal. To solve the problem, the first step is to identify the cause of the problem. Professional elevator manufacturers have strict testing, and promotional activities are underway. Welcome to consultThe speed circuit is the circuit that switches the motion speed and speed of the actuator in the hydraulic system of the guide rail hydraulic lifting platform. Mainly including valves, pumps, and actuators. The commonly used speed circuits include speed circuits, high-speed circuits, and speed switching circuits.Antony,When using an electric mobile scissor lifting platform outdoors, if the wind force exceeds level please stop using it; When the lifting height exceeds meters, the wind ropes at the four corners of the hydraulic lift platform should be tightened and fixed, and the support legs should be reinforced for protection and stability to avoid safety accidents caused by excessive swinging of the electric lifting platformThe precautions to consider when selecting a hydraulic lift oil tank include: considering the structure of the oil tank, the partition in the traditional oil tank cannot settle dirt. A vertical partition should be installed along the longitudinal axis of the oil tank, with a space left between one end of the partition and the end plate of the oil tank to connect the gaps on both sides of the partition. The inlet and outlet of the hydraulic pump are arranged on both sides of the partition at the disconnected end, so that the distance Z between the inlet and return oil is far, The hydraulic oil tank has more heat dissipation effect.After long-term use of the automatic lifting platform equipment, it is inevitable that some malfunctions will occur. In order not to affect work, it is necessary to promptly solve the difficulties in starting the motor and abnormal sounds. Generally, due to overload, insufficient power supply, and a small cross-sectional area of the power supply cable, the starting voltage drop is too large and the price of the cargo elevator is reduced.

Before installation, the installation personnel should confirm the infrastructure such as the foundation and shaft,BelskbiavaHydraulic lifting platform, leveling, and alignment points, and confirm that the foundation meets the requirements before construction.When working on scaffolding without scaffolding or without railings, safety belts must be used or other reliable safety measures must be taken.The hydraulic elevator overflow valve can also generate high noise. When air is mixed in hydraulic oil, the overflow valve is stuck or severely worn, resulting in unstable pressure regulation of the overflow valve, and the relief time of the overflow valve is too short, it is easy to cause the pilot valve performance of the overflow valve to be partially stable, causing air to vibrate inside the pilot valve and generate noise. So we need to regularly clean the overflow valve. When the overflow valve is damaged or severely worn, it should be replaced.build,I believe many people want to know about the maintenance issues of guide rail hydraulic lifting platforms, as it is related to their service life. During use, frequently check the connection of each part. If loose, tighten it. When the body is under pressure, the tightness of the connecting bolts of the body should be checked (the pressure state that can be used). All connecting shafts should have split pins and hydraulic cargo elevators should be fully opened.The combined platform is often used in small workshops with small volume of goods. However because this platform needs to complete two functions at the same time, it inevitably increases the distance of handling tools/vehicles in the workshop.The above are the working principles of three common elevators, and there are also some forms of elevators that are not common, such as cylinder mounted elevators, curved arm elevators car mounted elevators, etc. Their common feature is the hydraulic principle for operation, because the stability of the hydraulic system can bring better user experience and safer operation to the equipment, which has been favored by many users.

The noise and oil level of the elevator oil cylinder are too low. From the air at the connection of the oil filter or joint to the oil, the coupling inside the oil cylinder is loose. The internal fault of the oil cylinder is that the installation of the oil cylinder motor is not concentric. From the motor, the air and oil at the moving shaft are blocked. The oil return pipe of the oil filter is loose, and the air or oil pipe is on the oil surface, Mixing air into the oil to eliminate: The concentricity should be adjusted to within .MM. The coupling should be repaired or the oil pump should be replaced to increase the oil volume above mm in the oil filter and joint positions. The rotating shaft sealing ring should be replaced to clean the oil filter screen, filter the oil, lock the return oil pipeline, and extend the return oil pipeline below the oil level. If there is air mixed in the oil or the air in the hydraulic cylinder is not completely discharged, it will cause cavitation under high pressure and cause significant noise. At this point, it is necessary to exhaust the air in a timely manner.retailer,The elevator itself has a simple structure and is easy to maintain, which has been favored by a large number of enterprises and individual customers. Hydraulic elevator is a multifunctional heavy loading and unloading mechanical equipment. The lifting system of hydraulic elevators is driven by hydraulic pressure, also known as hydraulic powered elevators.Hydraulic oil deteriorates or produces impurities. After long-term use of oil pressure, there may be impurities or deterioration in the oil. Sampling inspection should be carried out to see if there are solid particles, discoloration, and odor. If necessary, the oil should be changed. There may be blockage in the hydraulic pipeline of the hydraulic cargo elevator. The hydraulic pipeline is also a very important part, and it is necessary to check whether the hydraulic pipeline is smooth. Focus on checking whether each type of hydraulic valve includes one-way globe valve, electromagnetic directional valve, proportional control valve overflow valve, etc. If there are problems, the hydraulic valve should be cleaned or replaced in a timely manner.When using hydraulic elevators the main causes of noise are mechanical mechanism failures, hydraulic system failures, electrical equipment or component failures, the manufacturer of hydraulic cargo elevators will introduce to you the reasons for the noise generated by hydraulic elevators.Belskbiava,The lifting platform is a multifunctional heavy loading and unloading mechanical equipment, which can be divided into fixed and mobile, guide rail and curved arm types. Fixed types include scissor elevators,BelskbiavaPlatform hydraulic lifting,BelskbiavaManual hydraulic lifting platform, chain elevators, loading and unloading platforms, and attached electric construction platforms.Set up warning lights around the guide rail type hydraulic cargo elevator equipment, and the warning lights will light up to warn operators when loading and unloading materials. Idle personnel are prohibited from entering the operating range.When installing, disassembling, and adjusting the rotating mechanism, attention should be paid to ensuring that the middle line is parallel to the middle line of the gear, and its meshing surface is not less than %. The meshing clearance should be suitable for the brakes of each mechanism. The clearance between the brake wheels should be regularly checked and adjusted to ensure its flexibility and reliability. There must be no dirt on the friction surface and it must be cleaned with gasoline or diluent.