Liberetz5mm thick stainless steel plateWhat should be paid attention to during seasonal work

When using this process, the following key points should be paid attention to: during the welding process, the correct included angle between the welding handle, welding wire and weldment should be maintained. The ideal caster angle of the welding handle nozzle is & deg; & mdash; & deg;, and the included angle between the welding wire and the weldment surface is & deg; & mdash; & deg;; correct the molten pool temperature, change the included angle between the welding handle and weldment, change the welding speed, etc. to change the molten pool temperature, so as to ensure Beautiful weld formation (uniform width, convex and other defects) During operation, the current shall be slightly larger than that of solid core welding wire, and the welding handle shall be slightly adjusted to accelerate the separation of molten iron and molten flux coating, so as to facilitate the observation of molten pool and penetration; when filling the welding wire, it shall be sent to places of molten pool and pressed inward slightly to ensure penetration and prevent concave; during welding, the welding wire shall be regularly sent and taken out,LiberetzPrice of stainless steel strip, and the welding wire shall always be ensured Under the protection of argon to prevent the end of the welding wire from being oxidized and affect the welding quality; pay attention to the welding quality of the arc and arc stop, and the spot weld shall be polished to & deg; the slope shall be gentle and pay attention to the defects such as arc pit and shrinkage hole during arc stop.There shall be a special storage rack. The storage rack shall be a wooden or painted carbon steel support or padded with rubber pad to isolate it from carbon steel and other metal materials. During storage, the storage position shall be convenient for lifting and absolutely isolated from other data storage areas. Protective measures shall be taken to avoid purification, collision with other components, purification and damage of iron metal.Liberetz,　　SPHCSPHC—& mdash; In the first place, s is the abbreviation of steel, P is the abbreviation of plate, h is the abbreviation of hot heat, and C is the abbreviation of commercial. It generally represents hot-rolled steel plate and strip.The slab solidified on the surface continues to be rapidly cooled through the secondary cooling section until the core becomes solid, and the whole continuous casting process of stainless steel pipe fittings is completed.Eastbourne,Model & mdash; High strength cutting tool steel, can obtain higher yield strength after appropriate heat treatment, and the hardness can reach hrc. It belongs to hard stainless steel. A common application example is & ldquo; Shaving blade & rdquo;. There are three common models: C and f (easy to process).The recrystallization temperature changes with the shape variable. When the shape variable is %, the recrystallization temperature drops to ℃, and the recrystallization annealing temperature of cold deformed austenitic stainless steel is ~ ℃. At ℃ it needs to be kept warm for h, fully burned at ℃ and then water-cooled.Ferritic stainless steel the Cr content of ferritic stainless steel is generally % ~ %, and the carbon content is less than .%. Other alloying elements are sometimes added. The metallographic structure is mainly ferrite, and there is no & alpha during heating and cooling=& amp; amp; gt;& gamma; The transformation cannot be strengthened by heat treatment. Strong oxidation resistance. At the same time, it also has good hot workability and certain cold workability. Ferritic stainless steel is mainly used to make components with high corrosion resistance and low strength requirements. It is widely used in manufacturing equipment such as production, nitrogen fertilizer and chemical pipelines.

AUSTENITIC FERRITIC duplex stainless steel. It has the advantages of both austenitic and ferritic stainless steel, and has superplasticity. Martensitic stainless steel. High strength, but poor plasticity and weldability.After the stainless steel pipe is completed, it must be moved, moved and moved for a long distance. If there is no bag, there will be scratches and scratches on the surface which will affect the appearance of the surface.Stainless steel pipe is a kind of economical section steel and an important product in the iron and steel industry. It can be widely used in life decoration and industry. Many people on the market are used to make stair handrails, window guards, railings, furniture, etc. and materials are common.Latest consultation,After fine tuning the molten steel temperature in the argon blowing station,LiberetzStainless steel pipe cleaning, it is lifted to the ladle rotary table for continuous casting.Austenitic stainless steel has good resistance to uniform corrosion, but there are still the following problems in local corrosion resistance: intergranular corrosion of austenitic stainless steel. Austenitic stainless steel will have intergranular corrosion when it is kept warm at ~ ℃ or cooled slowly. The higher the carbon content, the greater the tendency of intergranular corrosion. In addition, intergranular corrosion also occurs in the heat affected zone of the weldment. This is due to the precipitation of Cr rich CrC on the grain boundary. The chromium poor area is formed in the surrounding matrix, which is caused by corrosion of the primary cell. This intergranular corrosion phenomenon also exists in the ferritic stainless steel mentioned above.Stainless steel,W = (outer diameter wall thickness) & times; wall thickness & times; . = KGM (weight per meter).Carbon structure delivery status: delivered in heat treatment (annealing, normalizing, tempering after normalizing, high temperature tempering).That is stainless steel. The GB brand is CrNi. & mdash; it has better temperature resistance than it.Liberetz, and has superplasticity. Martensitic stainless steel. High strength, but poor plasticity and weldability.Add a small amount of sulfur and phosphorus to make it easier to cut.Vickers hardness stainless steel pipe Vickers hardness test is also an indentation test, which can be used to determine the hardness of very thin metal materials and surface layers. It has the main advantages of Brinell and Rockwell methods and overcomes their basic disadvantages, but it is not as simple as Rockwell method. Vickers method is rarely used in steel pipe standards.