HenzadaQuotation slurry pumpStatus of motion fault diagnosis

HenzadaCentrifugal slurry pump,　　Water pump control cabinet Time control: the chassis panel is equipped with a time setting button and a display. The user can control the opening and closing of the water pump according to the timing needs. It is suitable for the control of various timed or regular intermittent working modes.　　The structure of the submersible slurry pump will be more intuitive. First

　　Balance of.　　 selection of flow: single suction pump or double suction pump shall be selected according to the flow; single suction pump or multi suction pump shall be selected according to the lift.Henzada, the equipment will use centrifugal force to drive the liquid from the impeller to the outer edge and obtain energy, and then leave the edge of the impeller at a higher speedSan Jose,　　The premise of using this method is that the water gun must have sufficient flow during use, otherwise the effect of the submersible slurry pump may not be obvious.　　The submersible slurry pump is a slurry pump which is connected with the motor and works under the water at the same time. Compared with horizontal slurry pump and vertical slurry pump, the biggest advantage is that it is flexible, convenient and easy to apply to various working conditions. The most important technical point of submersible slurry pump is the tightness between its motor and pump body Stability and reliability of seals.　　Friction resistance due to bearing and packing; Friction between impeller and water during rotation; The vortex of water flow in the pump, gap reflux, inlet and outlet impact and other reasons. A part of the power must be consumed, so it is impossible for the water pump to completely change the power input by the power machine into effective power, in which the constant active power

　　 When stopping the operation of the submersible slurry pump, close the cock of the vacuum gauge and pressure gauge and the gate valve on the water outlet pipeline,HenzadaSubmersible pump can pump sewage, and After that, cut off the power supply of the motor. If the temperature of the environment is low, open the square plug at the lower part of the pump body to remove the remaining water to avoid frost cracking. During operation, the maximum temperature of the bearing shall not exceed ℃, and the quantity of calcium base grease used for lubricating oil bearing shall be the same as that of the bearing body　　Many customers need to replace the impeller after purchasing the slurry pump. What if the impeller of the slurry pump cannot be disassembled?　　 Another possibility is that the gas is sucked in when the pump is in use.Word of mouth recommendation,　　 install a valve to inject water at the water inlet and outlet. This method is to install a valve on the water inlet pipe of the submersible slurry pump and connect the water pipe to inject water into the pump. This is a common and simple method.　　 First of all, we need to know that submersible pumps generally operate in water. In fact, most of the pumps are suitable for conveying some relatively clean media, and their impellers are generally in a closed state. However, one of the media conveyed by sewage pumps may　　 We also need to make choices according to local conditions when we make purchases at ordinary times. For example, but its water output is not very large when it is used, so it is effective when it is used in many mountainous areas

　　 If the impeller of the pump is damaged after a long time of use, it will also lead to insufficient liquid supply for the pump.knowledge,　　 if the removed gasket is seriously damaged, a new gasket shall be replaced. The removed parts shall be cleaned with kerosene before assembly.　　On the rack.　　Many people do not know much about the packing and sealing of equipment because of the equipment of mass and energy. Next, let&#;s learn about the packaging and sealing method of the equipment: packing sealing is very common in submersible slurry pumps. This method has good sealing performance,　　It should be /-/ between. When the packing is worn, the packing gland can be properly pressed. If it is worn too much, it should be replaced. The whole commissioning process of the submersible slurry pump mainly includes the above five tasks, which are mainly to pay attention to the details and the phenomena occurred during the operation,HenzadaQJ submersible pump, and timely deal with the problems in time to avoid being on duty Accidents during operation cause losses.　　Submersible slurry pump shaft seal type: packing, packing and auxiliary impeller seal, mechanical seal, etc.　　 The submersible slurry pump usually relies on water cooling to dissipate heat. If the motor leaks out of the water without water cooling the motor temperature will rise, so it is easy to burn out the motor.