Lei ShufuLifting cargo elevator 1 tonThe manufacturer tells you the focus of buying

the platform is level with the ground, does not occupy the ground space and does not affect the passageway.The daily maintenance of the hydraulic lifting platform in normal use is essential, any possible problem cannot be ignored,Lei Shufu13 meter guide rail type cargo elevator, so in order to ensure that the process of using the hydraulic lifting platform for each operation What aspects do we need to check before operation? Today, the editor will give you a popular science.Lei Shufu,Novice operation: Since novices do not know much about mobile lifts and other aerial work platforms, they are prone to misoperation and cause equipment failure. Operators in this area need to study patiently and pass the training before they can operate and use.The daily maintenance of the hydraulic lifting platform in normal use is essential, but even if there is normal maintenance on the equipment, any possible problem cannot be ignored, so in order to ensure that the process of using the hydraulic lifting platform for each operation What aspects do we need to check before operation? Today, the editor will give you a popular science.Phichit,System: explosion-proof electronic control system, remote control system, P IC system.Check the limit switch to see if all the limit switches are loose. If so, please tighten them. Pay special attention to the ultra-high protection stroke of the hydraulic lifting platform to avoid accidents caused by the equipment exceeding the high safety height; check the pins (ear pins and center pins) Check whether the nuts, nuts, screws, etc. are loose, if any, should be reinforced immediately; ensure that the hydraulic lifting platform rises and falls smoothly; outriggers (for high-altitude operating platform)The hydraulic lifting platform is mainly the pressure transmission of hydraulic oil to realize the lifting function. Its scissor mechanical structure makes the lift stable, and the wide operating platform and high carrying capacity make the high-altitude operation wide and suitable for many people work at the same time. It makes high-altitude operations efficient and secure.

Many people think that the strength of the elevator itself is relatively high when using the elevator, so they did not strictly follow the installation method in the manual during the installation process, but they do not know that this will cause increased wear and tear of the parts and inflexible operation, and pay attention to the work The installation precautions corresponding to the environment should not be ignored. Correct installation, use and maintenance of elevators are an important part of ensuring the normal operation of mechanical equipment. Therefore, when you install the elevator, please be sure to strictly follow the installation and use related matters below, and assemble and use it carefully.Adjust the helmet lining of the helmet before using the helmet, and keep a certain space between the helmet lining and the helmet shell.Low cost: The cost is much lower than that of the scissor-type mobile lifting platform, so when purchasing a lifting platform, you must consider the scope of use of the lifting platform, the frequency of work,Lei ShufuGuide rail lifting cargo elevator, the load and other factors to choose a lifting platform that suits the work requirements .recommend,Correct construction elevator site inspection First of all, we need to check the foundation to see if there is any water accumulation, and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission, it can be divided into two types: open type and closed type. Of course, the lift also has a lot of safety equipment.Unscrew the screw on the dust-proof hole outside the flange of the elevator adjust the PCS system ring to align the side hole with the dust-proof hole, remove the motor shaft key.The parts such as reduction box and tighten the inner hexagon. After that, gearbox, external gear and hydraulic oil are all in accordance with the requirements in the table.

Correct construction elevator site inspection First of all, we need to check the foundation to see if there is any water accumulation, and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission, it can be divided into two types: open type and closed type. Of course, the lift also has a lot of safety equipment.Excellent quality,Unscrew the screw on the dust-proof hole outside the flange of the elevator, and tighten the inner hexagon. After that, remove the motor shaft key.Replace with new oil, do not use old oil intermittently, otherwise the moving parts in the system will accelerate wear.Precautions for using guide rail elevators Precautions for using guide rail elevators: It is strictly forbidden to overload, transport flammable and explosive products and other products.Lei Shufu,Lei ShufuFixed lifting cargo elevator,Today, the editor will talk about a series of safety devices and their uses on the guide rail hydraulic lifting platform.Regular maintenance Regularly check whether the circuit system of the hydraulic lifting platform is loose, and check whether the wires and cables are aging and damaged which may cause leakage of the line. If there is, it should be repaired in time to avoid electric shock.The anti-rust work of the aerial work vehicle generally needs to be paid attention to when the aerial work vehicle has not been used for a long time. How should we do anti-corrosion for the body of the aerial work vehicle? This is actually very simple. You don’t need to spend money to go to the repair station for anti-corrosion. As long as our car owners use some materials that they can find at hand, it can be realized. At the same time, paying attention to driving habits can ensure that the aerial work vehicle does not rust. Here are a few points that can be used as a reference.