HartwanMast type aluminum alloy hydraulic lifting platformProduct performance characteristics

The manufacturer of hydraulic cargo elevators reminds the use of guide rail hydraulic lifting cargo elevators. Guide rail hydraulic lifting cargo elevators: Do not stand within the specified range, draw on the guide rail lifting platform, prohibit any idle personnel from entering the work area, ensure that the work area is free of clothing, and maintain a clean and tidy workplace.The noise and oil level of the elevator oil cylinder are too low. From the air at the connection of the oil filter or joint to the oil, the coupling inside the oil cylinder is loose. The internal fault of the oil cylinder is that the installation of the oil cylinder motor is not concentric. From the motor, the air and oil at the moving shaft are blocked. The oil return pipe of the oil filter is loose, and the air or oil pipe is on the oil surface, Mixing air into the oil to eliminate: The concentricity should be adjusted to within .MM. The coupling should be repaired or the oil pump should be replaced to increase the oil volume above mm in the oil filter and joint positions. The rotating shaft sealing ring should be replaced to clean the oil filter screen, filter the oil lock the return oil pipeline, and extend the return oil pipeline below the oil level. If there is air mixed in the oil or the air in the hydraulic cylinder is not completely discharged, it will cause cavitation under high pressure and cause significant noise. At this point, it is necessary to exhaust the air in a timely manner.Hartwan,Therefore, the larger the shaking range, especially for mobile hydraulic cargo elevators. When the working height exceeds meters, the wind ropes at the four corners of the hydraulic cargo elevator should be tightened to strengthen leg protection, increase stability, and reduce shaking.Holy-Andre,Hydraulic lift cargo elevators belong to high-altitude work equipment. Small shaking of the scissor type structure is normal,HartwanHydraulic lifting platform manufacturer, but excessive deviation is a symptom. It is necessary to find the cause and make correct judgments in a timely manner. Generally speaking operations above meters are generally allowed. Due to its own weight, devices above this height begin to vibrate in different ranges. The vibration range depends on factors such as weight, lifting height,HartwanLarge hydraulic lifting platform, and intensity of high-altitude operations.Aluminum alloy elevators are different from other forms. This type of elevator is made of aluminum alloy material, which is lightweight and has a more beautiful appearance. The disadvantage is that it has a light load capacity and is only suitable for simple high-altitude maintenance work, and can only provide support for - people.Stability: The workbench should evenly withstand % of the MAX load capacity and be stable at the MAX elevation.

Set up warning lights around the guide rail type hydraulic cargo elevator equipment, and the warning lights will light up to warn operators when loading and unloading materials. Idle personnel are prohibited from entering the operating range.Low power consumption: Hydraulic elevators are driven by the pressure generated by their own weight,HartwanManufacturer of scissor lift, greatly saving energy. Long term improvement of various brand products such as elevator manufacturers, with complete designated products and quality assuranceDue to damage to the gear pump of the lifting cargo elevator equipment and no pressure lifting. Replace the gear pump.Highly recommended,When encountering signs of overheating in the electric motor it is necessary to park the car in a timely manner, clean the problem, and continue running. The motor bearings should be smooth and outstanding.Oil leakage is a common malfunction. Due to loose joints or damaged sealing rings, oil leakage may occur. Therefore, this fault can be solved by tightening the oil leakage joint or replacing the damaged sealing ring.The main device does not engage. When this fault occurs, check whether the three-phase power supply is normal, whether the internal and external emergency stop button switches, the electric lock switch are turned on, and whether the relay working indicator light is on.

The noise and oil level of the elevator oil cylinder are too low. From the air at the connection of the oil filter or joint to the oil, the coupling inside the oil cylinder is loose. The internal fault of the oil cylinder is that the installation of the oil cylinder motor is not concentric. From the motor, the air and oil at the moving shaft are blocked. The oil return pipe of the oil filter is loose, and the air or oil pipe is on the oil surface, Mixing air into the oil to eliminate: The concentricity should be adjusted to within .MM. The coupling should be repaired or the oil pump should be replaced to increase the oil volume above mm in the oil filter and joint positions. The rotating shaft sealing ring should be replaced to clean the oil filter screen, filter the oil, lock the return oil pipeline, and extend the return oil pipeline below the oil level. If there is air mixed in the oil or the air in the hydraulic cylinder is not completely discharged, it will cause cavitation under high pressure and cause significant noise. At this point, it is necessary to exhaust the air in a timely manner.Where to sell APIThe undercut length of the weld mm should not exceed % of the weld seam, and the depth should not exceed .mm.In addition, the lifting mechanism also needs to be equipped with powerful support frames. Therefore, the selection of lifting mechanism or lifting mechanism for hydraulic freight elevators cannot be generalized, but should be based on the working conditions of the elevator.Set up warning lights around the guide rail type hydraulic cargo elevator equipment, and the warning lights will light up to warn operators when loading and unloading materials. Idle personnel are prohibited from entering the operating range.Hartwan,The hydraulic pump produces noise. When the hydraulic elevator rises, the hydraulic pump runs at high speed. If there is a problem with the gears or bearings of the hydraulic pump, which causes periodic changes in the hydraulic system pressure, it will also cause resonance in the hydraulic system and generate noise.When the hydraulic oil is insufficient, the hydraulic pump will experience suction, causing air to enter the hydraulic oil and producing high noise.Considering the oil level in the oil tank, when all hydraulic cylinders in the system are extended, the oil level in the oil tank should not be lower than the Z-low oil level, and when the oil cylinders retract, the oil level should not be higher than the Z-high oil level. In fact, most manufacturers have noticed the above issues. The reason for the introduction is that most users can learn more about the equipment itself when using elevators