Create entry
World Encyclopedia  > category  >  Energy Encyclopedia   

SanaratHow to install the cold storage unitInfluence in pharmaceutical equipment industry

release time: 2022-06-29 15:46:08

Cold storage has strong stability. Polyurethane foam technology makes it have superior bonding performance. The firm combination of polyurethane rigid foam and carrier layer is the basic premise to ensure the stability of external insulation layer. That is, under the unfavorable local temperature and humidity conditions, the characteristics of the cold storage still do not separate and fall off from the carrier layer and remain stable under normal conditions.When installing the polyurethane insulation board, the adhesion between the panel of the polyurethane insulation board and the thermal insulation material is short and often high.Sanarat,Balance windows shall be provided for the fabricated controlled atmosphere storage.The importance of regular oil discharge, descaling and air discharge in the refrigeration system of the warehouse.Yamasa,Another reason is that there are many refrigerants in the system. In this case, find the leakage point first, focus on the connection of each pipeline and valve, repair the found part,SanaratPreservation of fruits in cold storage, and then fill in sufficient refrigerant.Before the acceptance and delivery of the project, the board surface shall be wiped clean. If there is any scratch, it shall be treated. There shall be no obvious scratch on the board surface. - floor installation of cold storage: first level the floor, then install the floor, select a beautiful floor and put it in a conspicuous place, and do a good job in the floor and evaporator drainage system.


SanaratHow to install the cold storage unitInfluence in pharmaceutical equipment industry



A large number of personnel are not allowed to select goods in the warehouse. Close the warehouse door in time. When the warehouse door is opened, pay attention to whether the air curtain is opened or the door curtain is placed properly. Turn off the lights when leaving the warehouse.Pressure leak test: the pressure leak test of the fresh-keeping warehouse system is the same as that of the sewage blowing working sample, which is required to be carried out by air compressor. If ammonia compressor is used, a special one shall be designated and the exhaust temperature shall be strictly controlled. When high pressure is applied, the method of segmenting and reducing the pressure difference shall be adopted.Initial stage of cold storage equipmentThe cheapest,SanaratVegetable fresh-keeping cold storage,All wiring shall be neat. All switches and keys shall be opened and closed sensitively, reliably and accurately. Special connectors shall be used for wiring and power protection shall be provided for the box and each power branch.Frequently observe the operation state of the heart compressor of the cold storage equipment and its exhaust temperature. During the season change operation, pay special attention to the operation state of the system and adjust the liquid supply and condensation temperature of the system in time.When installing polyurethane insulation board, ensure that its surface is smooth and flat without scratch and warpage.


SanaratHow to install the cold storage unitInfluence in pharmaceutical equipment industry



After being stored in the medical cold storage project, ventilating medical products may also emit some odors. Once these odors are stored in a certain quantity, they will also have a certain impact on other products. Therefore we must carry out regular ventilation in the process of daily use, so as to effectively reduce the storage time of products. If the medical cold storage project uses row tube refrigeration, the image of frosting may appear after use for a period of time. If we do not defrost in time, it will also affect the effect of. Therefore,SanaratWhere is the cold storage easy to install, I hope you must pay attention to defrosting.ranking,Anti odor floor drain shall be set on the pavement of refrigeration room and refrigeration unit room, and the height width ratio of floor drain water seal shall not be less than mm. The elevator shaft, it plays the main role of repeated operation and work. After being compressed by the wholesale compressor in the fresh-keeping warehouse, the refrigerant changes from no pressure to high pressure and low pressure to a proportional pressure and low pressure. This high and low pressure can achieve the principle of refrigeration under the action of other parts.The equipment that needs to be installed in the warehouse and put into the warehouse shall be installed in place or placed in an appropriate position in the warehouse; The wall warehouse board shall be installed from the corner of the warehouse body, good waterproof performance, fire and high temperature resistance, strong overload capacity, corrosion resistance, radiation protection and long service life. The corner shall be temporarily fixed with . color plate angle steel; When installing each wall panel, evenly apply two layers of foaming material on the joint surface of male and female groove, and apply one layer of foaming material when installing polystyrene wall panel. The blanking shall be uniform and continuous; After the wallboard is installed in place, pull rivets at the lap joint of the internal and external steel plates of the two wallboards for connection and fixation,Requirements for refrigeration equipment in quick freezing warehouse: the strict sealing of quick freezing warehouse is obviously different from that of ordinary quick freezing warehouse. Therefore the eccentric hook shall be loosened once before installation to ensure reliable locking during installation.Sanarat, how to seal the refrigeration equipment is the key. First of all, all through wall pipelines must be equipped with sleeves, the frost flushing water return pipeline must be equipped with U-shaped bend water seal, and the main frost flushing and return pipeline outside the warehouse shall be equipped with air filling port to prevent the gas in the warehouse from being pumped out of the warehouse by negative pressure. In addition, due to the good sealing of the quick freezing warehouse, the set fluctuation range of the warehouse temperature should not be too large to prevent excessive positive and negative pressure from damaging the warehouse body.During the use of cold storage, attention shall be paid to the collision and scratch of the storage body to avoid the depression and corrosion of the storage plate, which will seriously reduce the local thermal insulation performance of the storage body.At ordinary times, users should check the sealing degree of the gap of the cold storage, and notify the cold storage for maintenance in time if damaged parts are found.

Attachment list


0

The content of the entry is for reference only. If you need to solve a specific problem (especially in the fields of law, medicine, etc.), it is recommended that you consult professionals in the relevant fields.

Synonym

No synonyms