KrimavicCold storage installation Co., LtdIt can promote the development of society

The construction of small cold storage is widely used in life, manufacturing industry, etc. since cold storage is so widely used, do you know cold storage? Especially the construction process and steps of cold storage. Understanding the construction process and steps of cold storage is helpful for all links of cold storage maintenance.When the cold storage is used for the first time or shut down for a long time, it is strictly prohibited to stack goods in the warehouse. The warehouse must be slowly reduced to the required temperature. For the low-temperature warehouse, it needs to be cooled in stages to avoid sudden changes in the temperature difference inside and outside the warehouse, resulting in the warehouse body.Krimavic,The high temperature and high pressure of the compressor of the wholesale condenser of the fresh-keeping warehouse as the heat sink and heat exchanger needs to be dissipated and heat exchanged through the condenser, mainly to condense the refrigerant. The high-pressure temperature can reach Baidu, and the temperature will drop to degrees after condensation.Cold storage is mainly used for frozen processing and storage of foodLulea,. Maintenance of food cold storage. In a position convenient for operation outside the door of the refrigerator room, a main switch for cutting off the power supply of the refrigeration compressor shall be set. This switch shall be able to stop the operation of the refrigeration compressor and relevant signs shall be set. If the mechanical panel is set in the main room, which is made by high pressure foaming process and can be made into various lengths and specifications to meet the different requirements of the users.Operating the unit: regularly observe the oil level and oil return of the compressor and the cleanliness of the oil. If the oil is dirty or the oil level drops, it shall be solved in time to avoid adverse effects.

The new cold storage material is made of rigid polyurethane or polystyrene foam insulation sandwich panel, which is made by high pressure foaming process and can be made into various lengths and specifications to meet the different requirements of the users.Vacuum test: after the pressure test of the fresh-keeping storehouse system is qualified, the vacuum leakage test of the fresh-keeping storehouse system can be carried out. The purpose is to improve the air tightness under the vacuum condition of the fresh-keeping warehouse and prepare the conditions for the ammonia filling of the fresh-keeping warehouse system.Generally speaking, the construction of cold storage is to ensure the quality of buildings with its strict heat insulation, sealing, firmness and frost resistance.new product,Cold storage design step: the selection of cold storage refrigeration system the selection of cold storage refrigeration system is mainly the use of cold storage refrigeration compressor and air conditioning evaporator. Generally, small and medium-sized refrigerators are dominated by fully enclosed refrigeration compressors. Due to the small output power of the fully enclosed refrigeration compressor,KrimavicInstallation of vegetable fresh-keeping cold storage, the price is relatively cost-effective; Small and medium-sized refrigerators are generally dominated by semi closed refrigeration compressors; Semi closed refrigeration compressor is adopted for large and medium-sized refrigerated warehouses. When adopting, but the installation and management of refrigerated warehouses are cumbersome. When using the air-conditioning evaporator, the high-temperature cold storage uses the industrial cold fan as the air-conditioning evaporator. Its characteristic is that the temperature reduction speed is faster,KrimavicLarge cold storage installation company, but it is easy to lead to the water consumption of the cold collection; Medium and ultra-low temperature refrigerators are dominated by seamless evaporation pipe slots which is characterized by very good temperature control effect and moderate cold storage.According to the size and nature of the cold storage area and in combination with local regulations, the construction form of food cold storage warehouse is to determine the plane layout based on the site, whether it is a single-layer or double-layer warehouse, and the structure is the selection of steel structure or reinforcement solidification. Cold storage capacity, production process, refrigeration, product stacking, temperature, etc. are used to determine the size and location of the cold storage room, so that it can become a whole.The quick-frozen warehouse is easy to load and unload. All the plates and walls of the quick-frozen warehouse are produced by molds. You can choose tens of millions of products. Professional cold storage installation, installation of cold storage, cold storage construction, medical cold storage and transaction safety are guaranteed. Through internal concave convex groove connection, loading, unloading and handling are convenient. The installation period is short. Small and medium-sized cold storage can be delivered in - days, separated or increased or decreased according to the needs of users.

Here we focus on polyurethane. Polyurethane is an ideal cold storage material in the cold storage project. Superior bonding properties make the foam and metal panels form a solid whole, so that no other adhesive materials are needed. When polyurethane is used as a cold storage project, rigid polyurethane foam is formed between the panels of the storehouse panel, and then solidified and pressed to form a multi shape storeboard, because the metal plate can roll out different waveforms, so that the overall rigidity is stronger and the bearing capacity is higher. Polyurethane filler board can meet the firmness and physical requirements of exterior wall and can be used in various cold storage projects. It is technically feasible and cost-effective. Yuanbao refrigeration believes that polyurethane is one of the new cold storage materials with great development prospects in the future. The thermal insulation materials of cold storage engineering should not only have good thermal insulation performance but also be economical, applicable and environmental friendly. To ensure the smooth progress of our cold storage project, we should not only inquire about the raw materials of the cold storage, but also the types of cold storage. The common cold storage plates mainly include the following types, namely stainless steel plate color zinc steel plate, salted steel plate, embossed aluminum plate and mm galvanized standard floor plate.Safety production,Simple refrigeration is based on the volatilization of refrigerant in the condenser of the cold storage, so as to cool the refrigerant, and then input the refrigerant into the box or building of the refrigeration equipment to cool the air according to the heat exchanger. This kind of refrigeration has slow cooling speed, large total heat conduction temperature difference and complex system software,KrimavicPharmaceutical cold storage factory, so it can only be used in less places, such as brine ice making and cold storage with constant temperature requirements.There are several types of insulation materials. One is to produce and process plates with fixed shape and specification, fixed length total width and thickness. Plates of corresponding specifications and models can be selected according to the installation of the refrigerator body. High and medium temperature refrigerators generally use cm thick refrigerator plates, and ultra-low temperature refrigerators and freeze-cleaning refrigerators generally use cm or cm thick refrigerator plates; Another kind of sprayed polyurethane foam can be sprayed immediately into the finished brick or concrete warehouse. After forming, it is both waterproof and thermal insulation. Thermal insulation materials include polyurethane, polystyrene grease, etc. polyurethane is non hygroscopic and has good fire resistance, but the cost is high; Polystyrene resin has strong water absorption and poor fire resistance, but the cost is low. The structure of modern cold storage is developing in the direction of dress matching architecture. They are made into prefabricated components including steam barriers and heat shields to ensure field assembly. Its advantage is that the project construction is convenient, fast and movable, but the project cost is relatively high.If there is more air or refrigerant oil in the evaporator, the heat transfer effect will be reduced: once more refrigerant oil is attached to the inner surface of the evaporator heat transfer tube, the heat transfer coefficient will be reduced. Similarly, if there is more air in the heat transfer tube, the heat exchange area of the evaporator will be reduced, the heat transfer efficiency will be significantly reduced, and the decline rate of warehouse temperature will be slowed down.Krimavic,The machine room of ammonia refrigeration system shall be equipped with exhaust assembly; The exhaust fan shall adopt anti motor. When the power supply is cut off due to unexpected refrigeration, it shall be able to ensure the reliable power supply of the exhaust fan. The overload protection of the exhaust fan should be applied to the signal alarm system without directly stopping the exhaust fan. The button box of the exhaust fan shall be concealed in the wall outside the ammonia compressor room.Generally, in the actual operation of the refrigeration system, because the temperature conditions are constantly changing, only by relying on the careful operation of the cold storage management personnel and accurately adjusting the operation of the refrigeration equipment of the cold storage, can the refrigeration system always be in the ideal working state and achieve the effect of energy saving.Frozen and refrigerated storage began to change to shelf and pallet storage to complete the goods according to & ldquo; First in first out & rdquo; It is conducive to improve the quality of commodity storage and reduce loss.