AngaraHorizontal slurry pumpAdvantages of the product

　　In the application of pumps,AngaraDeep well pump, even the polluted water in cities needs to be purified. All these require its equipment to provide services for us. Without pumps our basic survival is a problem.　　The purpose is to inject liquid higher than . MPa from the water seal ring to prevent gas leakage into the pump when the suction inlet of the submersible slurry pump is in a vacuum state. When the water pressure in the pump is higher than . MPa, the sealing fluid .-. MPa higher than the pressure in the pump can be injected to seal and reduce leakageAngara,　　There are main reasons why the submersible pump is 'sick'. The rotation direction of the motor is wrong: please ensure that the rotation direction of the motor is correct before using the submersible sewage pump. Even if water is produced by reverse rotation,　　 The fan speed of the water pump is too low, and the air pressure and air volume are relatively small, so the heat cannot be dissipated.　　It can improve the mechanical efficiency to a certain extent. Moreover, the molecular structure of the coating itself has good compactness,AngaraSmall deep well pump, which can well isolate the air, water and other media from the pump impeller during use, and also reduce the corrosion and rust as much as possible　　When the pump is not in use, the pump shall be lifted away from the water source in time to drain the accumulated water in the pump, especially in cold winter. Then put it in a dry place. Conditional users can also apply oil to the key parts of the water pump and add lubricating oil to the bearing to prevent parts from rusting. in addition

　　The higher the specific speed of submersible slurry pump, the smaller the allowable cutting amount of impeller diameter. In addition to the sealing effect, the auxiliary impeller of the submersible slurry pump can also reduce the axial force.　　 tailings transportation, various tailings ore, pulp, pulp, coal slurry, slag, slag treatment, etc.　　 selection of pump head: generally, the pump head shall be determined by enlarging the margin of % - %.Honesty and mutual benefit,　　Body. So that the pump can realize high concentration transmission without auxiliary devices. The unique sealing device can effectively balance the pressure inside and outside the oil chamber, so that the pressure at both ends of the mechanical seal can be kept balanced, which maximizes the reliable operation of the mechanical seal and greatly extends its service life　　If the pump outputs more medium liquid, it will certainly do more work. If it sends less water it will certainly do less work, the reason for the motor body: the wrong connection will make the temperature rise rapidly when the equipment is used; In addition, there may be some phase to phase short circuits between stator windings, so when the situation is relatively minor, the motor is only in local places

　　It is an auxiliary means of on-site monitoring. During the operation of the submersible slurry pump, the condition of its overflow parts is very important to the overall operation. In order to let everyone know more about the equipment, we will learn how to adjust the impeller clearance of the pump in this issue. I hope it will help you.Direct material,　　The slurry pump should be larger. In addition to the existing industrial and mining applications of the vertical slurry pump the submersible slurry pump can also be used as a mobile slurry pump, such as sand pumping and prospecting on board; What are the advantages of the submersible slurry pump? The advantage of the submersible slurry pump is that it is convenient and flexible, easy to operate and submerged　　 hydrogen sulfide gas content mg/l　　If there are sundries blocked, the pump will not be filled with water. When this happens again, technicians need to properly adjust the liquid level in the pump sump to a proper height, and check the impeller. In case of damage or aging, it needs to be replaced in time,Angara,　　So it has a process of water diversion and exhaust. There are usually two ways to inject water into equipment. One is to directly inject water into the pump chamber, and the other is to pump out the gas in the pump to establish a certain vacuum and introduce the water source.　　Stop, then tighten the bearing seat, press down the nut,AngaraVertical heavy-duty slurry pump, and fix the axial position of the rotor. The latter submersible slurry pump uses a barrel support, which generally does not need to adjust the impeller clearance. Therefore, if there is a problem with the clearance in the future use, loosen the support clamp first, and say that the nut is loose　　If the shaft seal is not properly selected, it will not only require frequent maintenance during operation, but also leak a large amount of transmitted liquid.