ElgawaWQ submersible pump parametersAnalysis and design process and requirements

　　 Before starting the submersible slurry pump,ElgawaWater well pipeline pump, the rotor of the rotating pump shall be smooth and even, the outlet sluice valve shall be closed, and water shall be injected into the pump to ensure that the pump is full of water without air.　　Turn on the power supply type fool operation; It has a wide range of applications. In many cases, it belongs to a portable workstation,　　Belt drive bearing assembly: the bearing assembly of this series of pumps adopts cylindrical structure, which is convenient to adjust the clearance between the impeller and the front and rear guard plates, and can be removed as a whole during maintenance. The bearing is lubricated with grease.　　The installation of submersible slurry pump is a step that needs to be concerned. Since we all care about it,ElgawaScrew deep well pump, it is mainly because the installation will directly affect the use effect. The installation work should be seamless. Some key operating points can be seen when installing the slurry pump.Agadez,　　 Next, the water seal, lock ring and other parts need to be installed.　　Stability and reliability of seals between pump bodies.　　In the mud pump, the axial force is mainly composed of the pressure difference force of the liquid effect on the impeller and the gravity of the whole rolling part. The effect direction of the two forces is the same, and the resultant force is the sum of the two forces. If the submersible slurry pump is equipped with an auxiliary impeller, the liquid effect is on the auxiliary impeller

　　If there is a standby pump,ElgawaSubmersible pump can pump sewage, it is recommended that the two pumps be used in turn. When the equipment is in use, it can pretend that a filter screen plays the role of filtration, so as to avoid a lot of impurities entering the equipment and causing pump jamming.　　In recent years, domestic stainless steel pipeline pump products have greatly improved their technical level through introduction, absorption, renovation, digestion and innovation, especially the supporting products of some major technical equipment have reached or approached the advanced level of similar products.　　 Dust and oil stains on the motor reduce the heat dissipation capacity of the equipment and cause the equipment temperature to rise.Quality assurance,　　Screw it down, and then remove the bearing inner race, O-ring shaft sleeve and retaining sleeve in turn.　　 The gas inadvertently entered in the equipment is discharged and good sealing performance is ensured.　　 It may be that the motor power of the water pump is too large, the working current is too large, and the heat generation is too large, resulting in the high temperature of the vacuum pump.

　　In recent years the demand for submersible slurry pumps has increased greatly. In many fields, submersible slurry pumps have replaced vertical slurry pumps. What are the differences between the two? Let&#;s yze.Credit guarantee,　　 important parts shall be marked in advance to avoid errors during resetting. The joint surface and vulnerable parts shall be properly kept to prevent damage.　　 Check the wiring of the motor itself: it may be the high temperature caused by wrong wiring. If the wiring is wrong, quickly connect it back to the correct method.　　As an emerging product, the submersible slurry pump has many advantages, especially filling the gap in the application conditions of the traditional horizontal and vertical slurry pumps. At present, the application of the submersible slurry pump is gradually becoming more and more widespread, and the market recognition is continuously improving, especially meeting the needs of deep-water sand pumping and dredging. At present,　　The balance ring is also disassembled; Then remove the last stage impeller and the key back and the middle section including the guide vane; in addition, remove the impellers, middle sections and guide vanes at other levels in the same way until the submerged slag slurry　　The premise of using this method is that the water gun must have sufficient flow during use, otherwise the effect of the submersible slurry pump may not be obvious.　　The equipment is integrated with the oil cooler, with compact layout. The water pump meets the modular and integrated design requirements of diesel engine parts. The joint surface with oil cooler adopts rubber sealing method, which has good sealing effect. Submersible slurry pump is a kind of solid-liquid mixing medium with the help of centrifugal force