NagasakiDrilling fluid slurry pumpWhat are the ways of use

forming an impact force. The metal surface of the pump was fatigued and damaged by these impacts. Cavitation is caused by air bubble rupture and material stamping due to the difference in air temperature and pressure　　 The working properties of the two pumps are also different. Because the sewage pump is driven by a motor, it generally has good voltage impact resistance. The submersible pump is of the type of quick opening and quick closing, so it usually uses some small Flow and small pressure.Nagasaki,　　Ensure that the power supply voltage is adjusted to the standard power supply to solve the problem.　　 Next, it is necessary to check the water seal. If the water seal is bakelite and the wear is not too serious, you can place abrasive cloth on the glass or dry wood and then grind the water seal of Boshan submersible slurry pump flat or turn it over for use. However,NagasakiWQ submersible pump parameters, if the thrust rubber water seal is used, whenVallensbaek,　　Therefore, the correct selection of shaft seal can ensure the safe and stable operation of slurry pump.　　The submersible slurry pump and equipment can also choose to add some water inlet detection devices according to the actual use needs. The overheat monitoring devices are often used in a large amount in time, and the pump and motor of the equipment used in time are the same shaft, so　　Stop, then tighten the bearing seat, press down the nut, and fix the axial position of the rotor. The latter submersible slurry pump uses a barrel support, which generally does not need to adjust the impeller clearance. Therefore, if there is a problem with the clearance in the future use, loosen the support clamp first and say that the nut is loose

　　Will be scrapped. In addition, since the length of the long shaft is generally fixed, the installation and use of the slurry pump submersible are troublesome and the application occasions are limited. The submersible slurry pump is developed to adapt to increasingly complex working conditions and facilitate the use of users. Its use mode is more　　The equipment of this series of sewage pumps can be fixed or mobile. When the fixed active equipment is selected,NagasakiDeep well pump, the chain cable shall be separately threaded into (against the pump outlet, and its connection shall be parallel to the pump outlet) two eyebolts or lifting plates to lift the electric pump up and down. Evenly and slowly along the guide rail　　When the submersible slurry pump is used at ordinary times, cavitation usually occurs, which has a great impact on the impeller of the equipment itself. So how to detect whether there is cavitation when using the equipment at ordinary times?Production department,　　 The rotor assembly is designed according to the actual situation, and the operation is more stable!　　Balance of.　　Although the shaft seal occupies a small position in the pump, when we do not know the pump structure, we may make mistakes during disassembly. Let&#;s take a look at the correct disassembly of the impellerIndustry management,　　 During the installation of smooth bearing components, if the installation is correct, the smooth oil is appropriate, the repair is timely, and the delivery life will be long,NagasakiVortex pump and pipeline pump, the repair personnel should regularly repair the bearing components check the condition of the bearings and the smooth oil, and regularly add or replace the smooth oil during the work, and the interval and write　　Vertical height from water outlet center of pump base to flow destination (m)　　Wheel, mixing impeller and other main flow passage parts are made of high wear-resistant raw materials, which are wear-resistant, corrosion-resistant, non clogging, and have strong sewage discharge capacity, and can effectively pass through large solid particles. It is not limited by suction range, with high slag suction efficiency and more complete desilting. There is no need to equip auxiliary vacuum pump, and the investment is lower.Nagasaki,　　So it has a process of water diversion and exhaust. There are usually two ways to inject water into equipment. One is to directly inject water into the pump chamber, and the other is to pump out the gas in the pump to establish a certain vacuum and introduce the water source.　　 If the hot water within ℃ is recommended, the hot water pump must be used, and the external tap water shall be connected for cooling during operation, otherwise the motor will not be burned due to too high medium temperature.　　 in addition, the noise method directly detects the noise of the equipment in the detection process, so in fact, such measurement is not very accurate.