Vitti sur Seine15 meter hydraulic lifting platformWhat is the benefit if you complete the work in one go?

Working at heights is a common practice nowadays,Vitti sur SeineMobile elevator hydraulic lifting platform, but it also has a certain degree of danger. So people invented hydraulic lifting platforms, which are more convenient to help people complete high-altitude operations. However, people should also pay attention when using hydraulic lifting platforms, otherwise they can easily malfunction, which may lead to serious consequences. So what are the common faults of hydraulic lifting platforms?When using,Vitti sur SeineManual pressure relief of hydraulic lifting platform, the four legs should be firmly supported on a solid ground (based on the walking wheel about to leave the ground), and sleepers can be used when necessary.Vitti sur Seine,Readjust the overflow valve when the pressure is low. Adjust the oil level to be too low at % rated load, fill the hydraulic oil with suction oil, filter the blockage, and clean the oil suction section of the filter for air leakage. Check the oil suction pipe and joints; Tighten the joint. Replace the connector if necessary.After entering winter, elevators are prone to some small problems and malfunctions, which requires users to perform seasonal maintenance and upkeep on the elevator. Below, the editor will briefly introduce the winter maintenance precautions and key points of the elevator.Sinfra,Familiarity with the usage process and without a doubt this is the first thing to understand. There are two ways to understand it: first, carefully read the user manual provided by the manufacturer when the hydraulic lifting platform leaves the factory; The second is the equipment that needs to be installed. A professional installation technician will be dispatched to install the hydraulic lifting platform. After the installation is completed, relevant users will be trained on the operating process and safety precautions of the hydraulic lifting platform, and some maintenance matters in the future will also be explained; What should be paid attention to during the running-in period when using hydraulic lifting platforms? Check the wear of components. For newly processed and assembled components, there may be subtle deviations in shape and size that require a period of time for running-in. Therefore, during the running-in period, it is necessary to pay attention to whether there is any rapid wear. If there is any, the manufacturer of the hydraulic lifting platform should handle it in a timely manner to avoid equipment failure; Work between the pins and bearings to ensure that they are not worn, and add some engine oil or grease appropriately; Confirm if there is any noise during the running-in period. If it is found that the hydraulic lifting platform is noisy during operation, there is no need to worry in the early stage. If there are no major problems, run it several times more. After the running-in, the noise will naturally disappear. However, if there is noise for a long time and no signs of fading, please make sure to promptly produce it and solve the problem; Regularly check if the components are loose. Before use, check if there are any signs of looseness in screws, nuts, retaining rings, oil pipe joints, etc. If there are any, please reinforce or replace them in a timely manner to avoid accidents.Firstly it is necessary to use and operate the elevator correctly. The operators should receive systematic operation training: regular inspection of operating standards should be carried out, and any violations of elevator operation should be detectedAre there any damages to the wires and cables of the department. We need to quickly bandage and replace the damaged department.

Drain all the hydraulic oil in the oil tank, open the oil tank, take out the oil suction filter, clean it and return it to the oil tank. Install it in its original position. Fill the fuel tank with new oil.Slow down the smoothness and hydraulic oil of various departments such as the gearbox, gearbox, and external meshing gears according to the requirements in the smoothness table.Each department's electric brush should be kept clean, and the brush pressure should be adjusted to ensure that its area is not less than %Test method,Precautions for daily maintenance of hydraulic elevator: Check all hydraulic pipelines and joints of the hydraulic elevator. The pipelines must not be damaged and the joints must not be loose. All joints must be tightened.It is strictly prohibited to connect the motor of the lifting platform to the wrong power supply. It should be ensured that the voltage is V or V, which can cause uneven force distribution during the delivery of hydraulic oil, it can cause the elevator car to descend to the nearest floor position and open the door. Manual pump: When the system malfunctions, the manual pump can be operated to pump high-pressure oil to raise the car to the nearest floor position; Tank oil temperature protection: When the oil temperature in the tank exceeds the standard setting value, the oil temperature protection device sends a signal to suspend the use of the elevator. The elevator can only be started when the oil temperature drops.How much does it cost?,High altitude work requires the use of tool bags, and heavier and larger high-altitude work tools should be hung on stable components and cannot be placed randomly to avoid the occurrence of high-altitude falling accidents.Any machinery needs to be maintained after use, let alone large machinery. Poor maintenance of elevators after use can reduce the lifespan of elevators. Today,Vitti sur SeineDouble shear hydraulic lifting platform, the editor will tell you how to maintain elevators after use. In order to maintain the good technical condition of elevator machinery, ensure the safe use of on-site construction machinery, extend the service life of equipment, construction enterprises must maintain according to the relevant regulations According to maintenance regulations, necessary equipment maintenance work should be carried out. It is not allowed to focus solely on the use and maintenance of the equipment. It is strictly prohibited for equipment to be taken out of warranty or repair.What should I pay attention to when starting a new mobile elevator? High priced and various specifications of scissor lift manufacturers welcome scrap merchants, enterprises, and power departments to visit and negotiate with the company!Vitti sur Seine,Elevators are now very popular among people and can easily transport goods to high-rise buildings. Among them, hydraulic elevators are more popular among people, and people can choose the one that suits them according to their actual situation. However, during normal work, it is important to pay attention to the lifting speed of hydraulic elevators and avoid making mistakes. So what factors will affect the lifting speed of hydraulic elevators?What are the advantages of installing a guide rail type elevator for goods? The advantages of civil engineering are easy to install: there is no need for a machine room above the shaft, and the top layer can be installed at a height of more than meters. The computer room can be located within a radius of meters of the shaft, occupying an area of only - square meters. The hydraulic elevator is not equipped with a counterweight device to improve the utilization rate of the shaft area. The load and load cylinder of the hydraulic elevator directly act on the foundation pit, and the strength requirement for the shaft is low. A brick structure or brick concrete structure shaft is sufficient.Are there any damages to the wires and cables of the department. We need to quickly bandage and replace the damaged department.