AtsugiLong shaft submerged slurry pumpPrinciple of correct working direction

　　The high-efficiency slurry pump has three characteristics: first,　　 Check the winding of the motor: if the winding is damp or there are dust, which may reduce the insulation of the winding, it should be removed immediately.　　Water pump is a kind of machinery that pumps energy liquid. It is a machine that converts the mechanical energy of the prime mover into the potential energy of the pumped liquid. Driven by power machinery, it can pump liquid from low to high or far away to serve production.Lubango,　　Screw it down, and then remove the bearing inner race, O-ring,AtsugiDrilling fluid slurry pump, shaft sleeve and retaining sleeve in turn.　　First let&#;s talk about the familiar vertical slurry pumps. Here we refer to ZJL and SP submerged slurry pumps. Strictly speaking,AtsugiVertical centrifugal slurry pump, the submersible slurry pump is also a vertical slurry pump, because its axis is basically vertical when it works, but it can be completely immersed in water when it runs, so it is a good choice　　How to avoid this situation when the equipment is in use.

　　The water pump can be used to transport and pressurize clean water without impurities, such as apartment, residence, villa water supply, factory water supply, water supply system, drinking water system and water treatment. In short, there are many uses.　　The casing ground wire of QW (WQ) submersible non blocking sewage pump needs to be properly connected in strict accordance with relevant regulations. In order to ensure personal safety during operation, it is prohibited to do 'open' in the water of adjacent equipment and people during the operation of electric pump~ Or move in case of accident due to electric pump leakage.　　The above is the correct sequence of impeller disassembly of submersible slurry pump. Because different types of pumps have some differences in structure, we also need to refer to the instructions when disassembling.Bidding,　　Will be scrapped. In addition, since the length of the long shaft is generally fixed, the installation and use of the slurry pump submersible are troublesome and the application occasions are limited. It is normal to use the equipment for a long time, for example, when the submersible slurry pump is used at ordinary times,AtsugiVertical heavy-duty slurry pump, air holes usually appear　　Ordinary vertical motor can be used without waterproof, while the motor shaft and pump shaft of submersible slurry pump are coaxial, so the motor must be waterproof and sealed, and the motor and pump can be immersed in liquid at the same time; The vertical slurry pump is an early product, and the submersible slurry pump is a newly developed product according to the market demand　　The application of pumps involves all aspects of work and production, and the types of pumps are also diverse. Some of the same pump have several names, and some of the names are very similar, which makes it difficult to distinguish. Today, we will introduce the submersible pump and the submersible slurry pump. Is there any difference between the two

　　 for screws that are too tight or rusted for a long time, the nut can be lubricated with kerosene prepared in advance, or the nut can be gently knocked with a wooden hammer and then removed. This method can also be used in slurry pumps and other places.market,　　The submersible slurry pump shall be shut down for inspection in time in case of machine problems during operation, which will cause certain economic losses to us.　　First of all, the slurry pump is divided into three categories from the installation method: horizontal slurry pump, vertical slurry pump, submersible slurry pump horizontal slurry pump: also known as dry installation slurry pump, because it is installed on the ground and the surface of the pump body cannot contact the slurry, it is called dry installation. When this type of pump is installed,　　 install a valve to inject water at the water inlet and outlet. This method is to install a valve on the water inlet pipe of the submersible slurry pump and connect the water pipe to inject water into the pump. This is a common and simple method.Atsugi　　 After each use of the equipment, high-pressure water should be used to wash the pump and pipes. The washing can be stopped until the water has no impurities.　　 bind the exposed copper wire to the cable core evenly, heat it with an electric iron and infiltrate tin evenly.　　If the submersible slurry pump cannot be installed and operated, the blank operation point can be supplemented.