Tuusula 40Cr thick wall seamless pipehere has

I-beamClassification introductionTuusula ,They are not affected by surrounding factors and processes including corrosion. Miscellaneous scabYichin,Xhy- series high hardness alloy I-beam; Undertake drawings and process wear-resistant pipes（ Φ ≥mm）； Undertake the processing and production of vulnerable parts of cement machinery; Welding technology consultation and service; The wear-resistant layer of alloy wear-resistant plate of high chromium heap welding flux cored wire series is mainly high chromium, as well as manganese, molybdenum, niobium, francium and other components. The alloy carbide formed has strong stability at high temperature.I-beam is divided into ordinary I-beam and light I-beam. The specification of hot rolled ordinary I-beam is -#. The specification of hot-rolled flexible I-beam supplied through agreement between the supplier and the buyer is -#. I-beam is mainly used in building structure, vehicle manufacturing, other industrial structures and fixed panels and cabinets. I-beam is often used together with I-beam.Carburizing: carburizing is the process of penetrating carbon atoms into the surface layer of steel. It also makes the low-carbon steel workpiece have the surface layer of high-carbon steel, and then after quenching and low-temperature tempering, the part of the workpiece can maintain the toughness and plasticity of low-carbon steel.

Using alloy pipe to produce ring parts can improve the utilization rate of raw materials, simplify the production and manufacturing process, and save raw materials and production and processing construction time, such as roller bearing ring throwing Nowadays, seamless steel pipe has been widely used to produce hydraulic jack sleeve.The fourth is the welding process method to ensure the strict implementation of the special operation method of galvanized pipe. The welding process includes pre welding groove inspection, control of welding process parameters and operation methods, post welding appearance quality inspection and post welding nondestructive testing if necessary. Control the welding level and the amount of welding materials at each crossing.Defects of alloy pipe and solutions:How many?,→ under the same section load, the weight of hot-rolled H steel structure is reduced by % - % compared with the traditional structure. Cross rolling pass system. This pass system refers to that the two open legs of the I-beam pass are not on the same side of the waist at the same time, and the waist has an included angle with the horizontal axis.Application characteristics of I-beam:

Because alloy pipe is a very unique pipe fitting, we must use appropriate methods to carry out installation in the case of installation, when installing alloy pipes, we will use some flanges and elbows to fix them, so as to ensure that the raw materials can be fixed very well. Therefore,Tuusula How much is the I-beam rental per ton, when we carry out use, we must ensure the quality of flanges and elbows, so as to ensure the actual effect of alloy pipe assembly. If there are instrument panel components that must be assembled on the pipeline, they must be installed together.Production department,Alloy tube is widely used in our daily life, which provides us with great assistance. So what industries are alloy tubes applied to? Let&#;s follow the steps of all manufacturers and have a look together:The allowable deviation of vertical installation of galvanized pipe is mm per meter, and the allowable deviation above m is no more than mm. The allowable deviation of horizontally installed pipes is mm per meter.After determining the reasonable pickling agent and polishing solution, it is very easy to carry out hot galvanizing for relevant alloy pipes. Use 'phosphating treatment' to degrease the pipes of electrolytic machine equipment, put them into the aqueous solution with zinc salt after pickling and passivation, connect the negative level of electrolytic machine equipment, put them into the cold-rolled steel plate in the direction corresponding to the pipes, and connect the switching power supply, If the current flows from the positive stage to the negative stage, a layer of zinc is deposited in the pipe.Tuusula ,The sodium cyanide passivation treatment of alloy pipe can be divided into four categories. Before passivation treatment, the surface of alloy pipe shall be clear of oil stains, pickled and passivated. Passivation treatment can be carried out only after the surface is cleaned and the workpiece of alloy pipe products can be infiltrated into aqueous solution. The passivation treatment of the alloy tube in sodium cyanide transforms the surface layer into a very thin passivation treatment film, which determines that the color of the surface layer has no change before and after passivation treatment, and the reproducibility of the solution is good. Special rolling method. When it is difficult to roll the required I-beam by the usual rolling method for some reason, the special rolling method can be used to make full use of the skills of uneven deformation and pass design. For example, when the billet section is narrow and wide I-beam is required to be rolled, the wave rolling method can be used; for example, when the billet is wide and small I-beam is required to be rolled, etc.It is widely used in various fields of national economic construction, such as buildings, bridges, oil drilling platforms,Tuusula How many kilograms per meter of 80 seamless pipe, vehicles, highways, subways