BrugesSelf priming slurry pump wholesaleAccuracy analysis of

　　When using the submersible slurry pump, we should do a good job in all aspects of commissioning and precautions. We also need to do a good job in protecting the equipment parts and some parts of the motor. Only in this way can we avoid the impact of water and other impurities entering the motor　When using the submersible slurry pump,　　To sum up, we can know that the submersible sewage pump is both a submersible pump and a sewage pump, depending on what the user is used to calling it in use.　　According to the user&#;s requirements, the motor can add a variety of protection devices such as water inflow detection and overheating, so that the product can operate safely for a long time under adverse working conditions.Mogadishu,　　It is an auxiliary means of on-site monitoring. During the operation of the submersible slurry pump, the condition of its overflow parts is very important to the overall operation. In order to let everyone know more about the equipment, it is necessary to go to the relevant product catalog or sample, and make correction according to the performance table or performance curve of the model to see whether the normal working point falls in the priority working area of the pump.　　 the front and rear bearing glands are equipped with oil seals,BrugesVortex pump and pipeline pump, which are padded with green paper or asbestos. There is a gap of .- mm between the rear gland and the bearing.

　　When the water pump is driven by electricity or diesel engine, its impeller (like an electric fan) rotates wildly, thus forming a vacuum in the impeller. In this way, the atmospheric pressure will move the water pressure to pump water. In fact, from a al point of view, it is to convert electrical or chemical energy into gravity　　 Long continuous operation time. Because the pump and motor are coaxial, the shaft is short, and the rotating parts are light, the radial load on the bearing is relatively small, and the service life of the submersible sewage pump is much longer than that of the general pump.　　Fourth, model selection parameters: outlet diameter, flow, dust, motor power, impeller speed, pumping rate, maximum particle and weight.Convenient and efficient,　　Many users, including new practitioners of slurry pumps, often fail to distinguish the difference between submerged vertical slurry pumps and submerged slurry pumps. The names of submerged and submerged slurry pumps seem similar, but there are essential differences. What is the difference between submersible slurry pump and vertical slurry pump?　　Be sure to choose a pump that is more suitable for use.　　For example, it has a great impact on the impeller of the equipment itself. So how to detect whether the equipment has cavitation during use?

　　The submersible slurry pump may be blocked when it is used at ordinary times. In particular, some equipment is frequently used at ordinary times but the maintenance work is not done well when it is used, so it will be blocked after being used for a period of timeQuality management,　　Rotate in the rolling direction until the friction between the impeller and the front guard plate stops, then use the adjusting bolt to move the rotor backward, record the forward and backward movement gap, evenly distribute it between the front and rear guard plates of the impeller until the gap between the impeller, the front guard plate and the rear guard plate is flat, stop, and tighten the two dust discs and fasten them on the shaft. adjustment　　The water pump is not installed firmly or installed too high.　　The non service life of the equipment is not as long as possible. If it is not used for a long time, it will not only easily corrode the parts but also reduce the service life of the parts.Bruges,　　Generally, and the operation is reliable. Why not more than meters? This is the crucial technical point of the submersible slurry pump, because the current sealing technology in China is more than meters, not because the slurry pump has a problem,BrugesWear resistant slurry pump,BrugesSubmersible sewage pump, but because　　 When the slurry pump fails to absorb water during operation, it may also be because the bottom valve is not opened. At this time, it is necessary to check whether the bottom valve is open and make corresponding adjustment.　　Stability and reliability of seals between pump bodies.