CagliariElevator goods laddermanufacturer

The anti-rust work of the aerial work vehicle generally needs to be paid attention to when the aerial work vehicle has not been used for a long time. How should we do anti-corrosion for the body of the aerial work vehicle? This is actually very simple. You don’t need to spend money to go to the repair station for anti-corrosion. As long as our car owners use some materials that they can find at hand,CagliariFactory freight elevator lifting, it can be realized. At the same time, paying attention to driving habits can ensure that the aerial work vehicle does not rust. Here are a few points that can be used as a reference.Correct construction elevator site inspection First of all, we need to check the foundation to see if there is any water accumulation, and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission, it can be divided into two types: open type and closed type. Of course, the lift also has a lot of safety equipment.Cagliari,When using mobile lifts for high-altitude operations, the safety requirements and specifications of the project site must be complied with.Before wearing the helmet, check whether the helmet shell, hat lining, and chinstrap are complete and safe and effective.Mechanisms: Mechanisms such as tabletops, track grooves, wire ropes, chains, and pulleys are made of solid materials to ensure safety.Liperi,The water cooling of the hydraulic station is generally tube-type water cooling, and its type selection is based on the heat load to calculate the heat exchange area, while its air-cooled elevator is carried out by using an air cooler, and it is The heat transfer capacity is calculated according to the heat load, and then the type selection calculation is carried out under the condition that the flow rate can be satisfied. Therefore, these two kinds of cooling are not the same, and there is a big difference. Long-term promotion of freight elevator factories and other, Long-term cooperation, mutual benefit and win-win. If you choose the wrong supplier, you will be overwhelmed with all kinds of after-sales troubles in the later stage. Recently, I have seen many netizens report the problem of very loud oil cylinders. Today, the editor will simply popularize the knowledge for everyone.Uses: The scissor-type fixed lifting platform is mostly used for the transportation of goods between the height differences of the production line,CagliariElevating cargo elevator Elevating cargo elevator, the loading and unloading of materials, the adjustment of the working height during the assembly of the workpiece, the lifting of parts during the assembly of large equipment, and the storage and unloading place and Forklifts and other handling vehicles are used for fast loading and unloading of goods, car lifting, fixed three-dimensional parking and other places.Are the water cooling and air cooling of the hydraulic station the same?

The scissor-type fixed lifting platform is a kind of transportation and handling equipment for transporting goods from a certain height to another height. After the operation is completed, the platform is level with the ground, does not occupy the ground space, and does not affect the passageway.The ripper does not move up or down or the lifting force is weak: the pressure adjustment of the relief valve does not meet the requirements and adjust the pressure to the required value; see the cleaning in item above for the internal leakage of the oil cylinder; the reversing valve is locked or internal leakage; The oil tank is blocked; the oil supply pump is faulty; the one-way valve checks the wear and damage of the one-way valve core and valve seat, and whether the one-way valve spring is fatigued or deformed.The wrong connection of the motor of the elevator When a coil, coil group or one-phase winding is reversed, it will cause a serious imbalance in the three-phase current and cause the winding to overheat.Inspection standard,The boxes and distribution boxes of the hydraulic lift are always kept clean, and the dust on the electrical equipment is cleaned in time.The use of the hydraulic lifting platform The user can choose the power mode and configuration according to his own scope of use: the power system includes: DC power supply, single-phase or three-phase power supply, and diesel engine.The contact opening and closing of the travel switch of each safety device must be reliable, coil group or one-phase winding is reversed it will cause a serious imbalance in the three-phase current and cause the winding to overheat.total cost,When installing, dismantling and adjusting the slewing mechanism, care should be taken to ensure that the centerline of the slewing mechanism reducer is parallel to the centerline of the gear, the meshing surface is not less than % and the meshing clearance is suitable.Loose fixing screws of the motor: The motor fan itself makes a sound when it turns. If the screws fixing the motor are loose, coupled with its own vibration, so it makes a sound; the joints of the pin shafts are dry, lack of oil iron The rigid friction between the parts and the iron parts will not only damage the parts but also produce abnormal noises, pay attention to timely maintenance and frequent refueling; if the hydraulic lifting platform does not rise, there is air in the hydraulic oil,CagliariGuide rail chain cargo elevator lifting, you can open it to exhaust If the hydraulic oil is solidified: just replace the hydraulic oil; oil leakage: check whether there is oil leakage at the joints of each oil pipe, if there is oil leakage, replace it in time; reverse the motor: check whether the wiring is wrong; (no Those who understand electricity, timely manufacturers of hydraulic lifting platforms)Before the elevator manufacturer connects the motor to the elevator, please make the keyway of the motor shaft perpendicular to the tightening bolt. In order to ensure uniform force, please screw on the mounting bolts at any diagonal position first, but do not tighten them tightly, then screw on the other two mounting bolts at diagonal positions, and then tighten the four mounting bolts one by one. Finally tighten the tension bolts. All tightening bolts need a torque wrench to fix according to the marked fixed torque data and check whether the lift and lifting platform are used.How should we check the construction site of the construction hoist? you know?Cagliari,Brake operators of various mechanisms on the equipment should regularly check and adjust the gap between the brake shoe and the brake wheel to ensure flexibility and reliability. Long-term promotion of freight elevator factory, old brand, price advantage, quality guaranteed!In addition to the fixed mode, the elevator also has a vehicle-mounted mobile type. As the name implies, it combines the lifting equipment with the vehicle-mounted system. Such a lifting equipment is very flexible to move, and of course it is more useful. For example There is this kind of lifting equipment in the airport and it is also possible to install this kind of equipment in stations or stadiums. Since it can be moved, the scope of operation is not limited to a certain place, and it can be used wherever lifting operations are required. It can be used. For example, the height of some advertisements is relatively high. At this time, mobile lifting equipment can be used to send billboards or staff to the designated height to work. This kind of equipment can also be divided into two types according to the driving mode: hydraulic lifting and electric lifting. The so-called hydraulic lifting is driven by hydraulic oil to reach a specified height. The electric mode is driven by a motor or geared to lift to A certain height, but at present, hydraulic lifting platforms are more widely used.What types of lifts are there? There are many types of this equipment, for example, it can be divided into fixed lifting devices and vehicle-mounted lifting devices according to the form of movement. The so-called fixed lifting means that it is generally installed in one place and fixed, and then the lifting operation can be carried out. This type of lifting equipment is generally used more on the assembly line. Some large-scale production lines need to move the material when loading materials. Lifting to a certain position, and then putting it into the production line for production, a special lifting device is required to be fixed at a certain position of the production line.