CardiffSmall deep well pumpTeach you to choose the right one

　　 If the power cord is not well contacted, it will also lead to the burning of the motor.　　Function of shaft seal of submersible slurry pump: the main of shaft seal is to prevent high-pressure liquid from leaking out of the pump and prevent air from entering the pump.Cardiff,　　What is the solution to this situation?　　 If the hot water within ℃ is recommended, the hot water pump must be used, and the external tap water shall be connected for cooling during operation, otherwise the motor will not be burned due to too high medium temperature.　　Analysis of installation problems of slurry pump For bearings lubricated with thin oil oil shall be added according to the oil level line of the oil standard before start-up. Add (HL hydraulic oil in winter and (hl hydraulic oil in summer. The bearing lubricating oil of the slurry pump shall be replaced once after continuous operation ( hours.

　　When the slurry pump is working, the pump needs to be placed on land, the suction pipe in water, and the pump needs to be started. Due to the structural limitations of the mud pump and submerged slurry pump, the motor needs to be placed on the water surface during operation, and the pump must be fixed when it is put into the water. Otherwise, the motor will fall into the water　　 Easy installation and maintenance. Small submersible sewage pumps can be installed freely. Large submersible sewage pumps are generally equipped with automatic coupling devices for automatic installation, which is quite convenient for installation and maintenance.　　 determination of model: for water pump or pump with physical and chemical medium similar to water, it is necessary to go to the relevant product catalog or sample, and make correction according to the performance table or performance curve of the model to see whether the normal working point falls in the priority working area of the pump.Development Curriculum,　　With the arrival of midsummer and the intensification of the contradiction between supply and demand of kerosene, the power supply across the country has been tense again, which has driven the hot sale of it and generators in the phase II market. According to relevant data, there is still a large gap after China&#;s power balance.　　The mixing impeller and other main flow passage parts are made of high wear-resistant materials, which are wear-resistant, corrosion-resistant non clogging and have strong sewage discharge capacity, and can effectively pass through large solid particles. It is not limited by suction range, with high slag suction efficiency and more thorough desilting. No auxiliary vacuum pump is required and the investment is lower. nothing　　 install the front pump shaft first and then the rear bearing for the slurry pump of the filter press of the cylindrical bearing box.

　　Circumference. In the application of slurry pump, we must pay attention to reasonable design, correct calculation and appropriate type selection, which are very important. In addition to the main wheel,CardiffWear resistant slurry pump, a set of stirring impeller is added at the bottom of the product, which can spray the precipitated slag into a mixture of water and solid particlesGood quality,　　Vertical slurry pump is an early product. Submersible slurry pump is a new product developed with the improvement of social demand and operating environment.　　ZGB and other series,CardiffHorizontal non clogging sewage pump, with complete models. Most of the vertical slurry pumps are AF foam pump, SP submerged slurry pump, SPR submerged rubber lined slurry pump, ZJL submerged slurry pump and other series, with complete models, flow passage parts and accessories; Third, from the number of impellers, the type of slurry pump is divided into single-stage slurry pump　　 Another possibility is that the gas is sucked in when the pump is in use.Cardiff,　　The solution to the excessive temperature of the water pump: when selecting the motor, it is necessary to select one that matches its power and speed. In addition, the cooling fan should be installed on the main shaft. It is also possible to appropriately increase the number of fan blades, but pay attention to adjusting the vacuum pump　　The development of submersible slurry pump is to adapt to increasingly complex working conditions, facilitate users to use and its use mode is more flexible. And it fills a part of the gap in the application of slurry pump. When the submergence depth is deep and there is no better slurry outlet, that is,CardiffSplit vertical pipeline pump, in the traditional slurry pump　　Avoid airborne sound transmission; Ensure the airtightness of machine room doors and windows. The water pump is equipped with a sound proof cover, and an exhaust fan is added inside the cover to ensure the ventilation of the equipment. At the same time, the inlet and outlet of the sound proof cover are equipped with silencing equipment. A vibration isolation platform is installed at the bottom of the water pump for foundation vibration reduction to isolate the vibration generated during the operation of the water pump