AllahabadBaigang deep well pumpSelection skills of operation methods

　　Screw it down, and then remove the bearing inner race, O-ring, shaft sleeve and retaining sleeve in turn.　　 When adding lubricating oil to the pump at ordinary times, the metering must be controlled, and the excess lubricating oil in the pump must be discharged and replaced regularly.Allahabad,　　It is worth noting that the QW mobile type is generally used without a fixed position, so it is usually used temporarily without an electric control cabinet, when the submersible slurry pump is blocked during use, but also cause serious damage to the equipment itself so it is also a reminder that we are using it tooPunjab,　　Submersible slurry pumps are mainly used in mining, metallurgy, coal, environmental protection, electric power and other industries to transport corrosive solid particle slurry. For example, in the field of chemical industry corrosive mixed pastes of chemical crystals are transported. Electric ash removal, coal washing plant slurry transportation, etc. Submersible slurry pump blade　　 We must choose to consider the actual use situation when making the selection, because there will be some difference between the marked head when using and the head when using. This is because the pipe itself　　The slurry pump of underground pump can also work normally.

　　Friction. Because if the surface of the pump is smooth when it is used, the equipment will consume less energy when it is used. Generally, the submersible slurry pump and impeller are sprayed with polymer composite materials for use　　 total depth of well or pool M　　The seal cannot bear the water pressure at this depth. Once the water leaks, the motor will not work normally, resulting in damage to the submersible slurry pump. The biggest difference between the submersible slurry pump and the horizontal slurry pump and the vertical slurry pump is that the motor of the submersible slurry pump and the shaft connected to the pump are integrated and sealed Closed.Quality Assurance,　　Discount. In order to meet the needs of industrial production and make the submersible pump to achieve the ideal use effect, accurate and reasonable selection is very important. In order to select the pump reasonably and correctly, the following aspects need to be considered: Selection of shaft seal form: shaft seal of submersible slurry pump　　 Then unscrew the nut at the front end of the pump shaft, remove the cover plate, and press out the middle impeller and water seal.　　 When the power supply voltage is too low, the pump will be overloaded, it may be lower than the rated voltage, so the current in the stator winding will also be

　　The submersible slurry pump is a kind of submersible pump which is connected with the motor and works underwater at the same time. In addition,AllahabadCirculating hot water pipeline pump, compared with horizontal slurry pump and vertical slurry pump submersible slurry pump has the great advantage of flexibility and convenience,　　 First, screw down the bolts on the side bearing pressure cap, and then remove the nuts used for the connection between the three parts: discharge section, stuffing box body and bearing body; Then screw off the round nut on the shaft,AllahabadQuotation slurry pump, and successively install the bearing inner race,AllahabadBooster pipeline pump, bearing gland and retaining sleeve　　Determine whether repair and replacement is required according to the wear condition of the ring; Check the insulation of the motor stator to see if there is any trace of chamber sweeping damage; Check whether there is sand deposition and sewage blockage at the pump bottom, whether there is sand deposition at the pool bottom, and whether it is necessary to cut off water and clear silt.　　The mixing impeller and other main flow passage parts are made of high wear-resistant materials, which are wear-resistant, corrosion-resistant, non clogging and have strong sewage discharge capacity, and can effectively pass through large solid particles. It is not limited by suction range, with high slag suction efficiency and more thorough desilting. No auxiliary vacuum pump is required and the investment is lower. nothingAllahabad,　　 Then tighten the compression nut on the packing gland evenly to make the liquid leak out in drops, and pay attention to the temperature rise outside the packing chamber.　　It is located in the middle, so it seems that many regions have good effects when using it.　　Rotate in the rolling direction until the friction between the impeller and the front guard plate stops, then use the adjusting bolt to move the rotor backward, record the forward and backward movement gap, evenly distribute it between the front and rear guard plates of the impeller until the gap between the impeller, the front guard plate and the rear guard plate is flat, stop, and tighten the two dust discs and fasten them on the shaft. adjustment