Kalyan Baigang deep well pumpPrecautions in handling and Application

　　 Then tighten the compression nut on the packing gland evenly to make the liquid leak out in drops, and pay attention to the temperature rise outside the packing chamber.　　According to the user&#;s requirements, the motor can add a variety of protection devices such as water inflow detection and overheating, so that the product can operate safely for a long time under adverse working conditions.Kalyan ,　　During the long-term overload operation of submersible sewage pumps,Kalyan Vertical multistage centrifugal pipeline pump, there are many cases of sudden abnormal failures of submersible pumps. Among them, there are some common obstacles, such as the submersible pump cannot be started after it is powered on or the motor speed cannot be started after the submersible pump is started. A very small wait　　When the pump is not in use, the pump shall be lifted away from the water source in time to drain the accumulated water in the pump, especially in cold winter. Then put it in a dry place. Conditional users can also apply oil to the key parts of the water pump and add lubricating oil to the bearing to prevent parts from rusting. in additionMemphis,　　It will burn out. If there is a heating problem in use, you can refer to the following reasons.　　 When starting the slurry pump, expand the pump inlet valve and close the pump outlet valve. Then start the pump. After the pump is started, slowly start the pump outlet valve. The size and speed of opening the pump outlet valve should be based on the fact that the pump does not vibrate and the motor　　The solution to the excessive temperature of the water pump: when selecting the motor, it is necessary to select one that matches its power and speed. In addition, the cooling fan should be installed on the main shaft. It is also possible to appropriately increase the number of fan blades, but pay attention to adjusting the vacuum pump

　　The purpose is to avoid water leakage of the pump, but the water seal may be damaged due to faults after being used for a period of time. Let&#;s learn how to replace the water seal.　　 It is not allowed to operate the electric pump at high lift for a long time, and try to control it within the range of the proposed use lift, so as to prevent the electric pump from burning out the motor due to overload.　　Many users, including new practitioners of slurry pumps, often fail to distinguish the difference between submerged vertical slurry pumps and submerged slurry pumps. The names of submerged and submerged slurry pumps seem similar, but there are essential differences. What is the difference between submersible slurry pump and vertical slurry pump?Application process,　　The use of water pumps for agricultural drainage and irrigation can improve the ability of agriculture to resist natural disasters increase production and ensure income,Kalyan Fire deep well pump, and provide material conditions for agricultural mechanization and water conservancy.　　 We must choose to consider the actual use situation when making the selection, because there will be some difference between the marked head when using and the head when using. This is because the pipe itself　　The submersible slurry pump shall be shut down for inspection in time in case of machine problems during operation, and regular maintenance shall be done. The equipment will not be used after burning out,　　Then it can enter into the volute pump housing. Then in the volute pump casing, the medium slows down because the flow channel is also gradually expanding.　　 The fire control cabinet has fault alarm . When a single fire pump is working, it is not easy to be found in time in case of insufficient water source, power circuit failure, resulting in damage to the fire pump. Using the fire control cabinet,Kalyan Rubber lining submerged slurry pump, the alarm of the control cabinet can remind each　　 If the head of the submersible slurry pump is too low or the head is higher than the practical condition, the flow will be large and the current will rise. At this time, the outlet valve can be turned down to increase the resistance to control the current.Kalyan ,　　It is also necessary to clean the ventilation duct to avoid blockage.　　Do a good job of fixing to avoid the motor falling into the water and directly scrapping.　　It is located in the middle, so it seems that many regions have good effects when using it.