South BostonVertical centrifugal slurry pumpSource direct supply manufacturer

South BostonIrrigation deep well pump,

　　Submersible slurry pump can be widely used in mining,South BostonSubmersible non clogging slurry pump, power, metallurgy, coal, environmental protection and other industries to transport abrasive slurry containing solid particles. Such as ore slurry transportation in metallurgical concentrator, hydraulic ash removal in thermal power plant, coal slurry and heavy medium transportation in coal washing plant, river dredging, etc. In chemical industry　　Rotate in the rolling direction until the friction between the impeller and the front guard plate stops, then use the adjusting bolt to move the rotor backward, record the forward and backward movement gap, evenly distribute it between the front and rear guard plates of the impeller until the gap between the impeller, the front guard plate and the rear guard plate is flat, stop, and tighten the two dust discs and fasten them on the shaft. adjustmentSouth Boston,　　Belt drive shaft seal: the pump seal can be divided into three types: packing seal, auxiliary impeller seal and mechanical seal. The packing seal and the secondary impeller seal will drip during the operation of the pump. Mechanical seal can make no water leak.　　The effective power is also called output power, which is expressed by PE. It is the effective energy obtained in the pump by the medium liquid output from the pump in unit time.Talisay City,　　Commodity.　　The high-pressure water flows to the space occupied by the original bubble at a very high speed, forming an impact force. The metal surface of the pump was fatigued and damaged by these impacts. Cavitation is caused by air bubble rupture and material stamping due to the difference in air temperature and pressure　　 There is also a vibration method to measure the vibration frequency of the pump, and the measurement is relatively simple. However, when using one method, the measurement results may have some errors. When using the submersible slurry pump, there are other vibration sources that will affect the measurement results, so it is actually the main

　　 If the hot water within ℃ is recommended, the hot water pump must be used, and the external tap water shall be connected for cooling during operation, otherwise the motor will not be burned due to too high medium temperature.　　 Shaft seal part auxiliary impeller shaft seal: through the impeller action of a reverse centrifugal force, prevent the slurry from leaking out. When the positive pressure at the inlet of the pump is not greater than % of the pressure at the outlet of the pump, the single-stage pump or the first stage pump in series can adopt the auxiliary impeller shaft seal, and the auxiliary blade shaft seal is not required　　 The rotor assembly is designed according to the actual situation and the operation is more stable!equipment maintenance ,　　 It may be that the motor power of the water pump is too large, and the heat generation is too large, resulting in the high temperature of the vacuum pump.　　What stands out is the sealing of the container. The seal is easy to install and maintain, stable and reliable, but the price is quite expensive.　　Rate.

　　The submersible slurry pump can be used to transport a lot of media containing solid particles when it is used at ordinary times, so it has an irreplaceable position when it is used. What is its own structure when it is used.Safety and health,South BostonVortex pump and pipeline pump,　　 The submersible slurry pump usually relies on water cooling to dissipate heat. If the motor leaks out of the water without water cooling, the motor temperature will rise, because the length of the long shaft is generally fixed, it is often troublesome to install it. Therefore, when it is used later, the place where it operates will also be limited. If the equipment willSouth Boston,　　 It may be that the motor power of the water pump is too large, the working current is too large, and the heat generation is too large, resulting in the high temperature of the vacuum pump.　　The above four methods can be used to detect whether the submersible slurry pump has cavitation because if the equipment is in use, it will also have a certain impact on other parts of the equipment. Sometimes submersible slurry pump　　 for screws that are too tight or rusted for a long time it will have a great impact on the operating efficiency. Even if the cavitation time is long, the nut can be lubricated with kerosene prepared in advance, or the nut can be gently knocked with a wooden hammer and then removed. This method can also be used in slurry pumps and other places.