OttawaWater well pipeline pumpWhat are the advantages and features

　　 the front and rear bearing glands are equipped with oil seals, which are padded with green paper or asbestos. There is a gap of .- mm between the rear gland and the bearing.　　Start the priming pump. Moreover, due to the structural limitations of the submersible slurry pump, the motor needs to be placed on the water surface for use during operation, and then the pump needs to be placed in the water for use. Therefore, the submersible slurry pump must beOttawa,　　 the insulation resistance between the shaking cable and the submersible slurry pump shall not be less than megohm.　　Avoid airborne sound transmission; Ensure the airtightness of machine room doors and windows. The water pump is equipped with a sound proof cover, and an exhaust fan is added inside the cover to ensure the ventilation of the equipment. At the same time, the inlet and outlet of the sound proof cover are equipped with silencing equipment. A vibration isolation platform is installed at the bottom of the water pump for foundation vibration reduction to isolate the vibration generated during the operation of the water pumpKisvarda　　Wheel, mixing impeller and other main flow passage parts are made of high wear-resistant raw materials, corrosion-resistant,OttawaVertical heavy-duty slurry pump, non clogging, and have strong sewage discharge capacity, and can effectively pass through large solid particles. It is not limited by suction range, with high slag suction efficiency and more complete desilting. There is no need to equip auxiliary vacuum pump, and the investment is lower.　　Screw it down, O-ring shaft sleeve and retaining sleeve in turn.　　The of descending axial force can be used for slurry transportation in power plants, hydraulic and other professions; The mechanical seal is tight and reliable, and the leakage probability does not exceed drops /min, which is mostly used to transport flammable explosive, toxic, strong corrosive and valuable liquids or materials with high temperature, high pressure and low temperature.

　　Second, the service life of the flow passage parts of the pump is relatively long, saving production costs.　　The water pump is not installed firmly or installed too high.　　After a certain value, water will also vaporize, which is called the vaporization pressure of water at this temperature.Professional is king,　　Only in this way can its service life be extended to a large extent.　　It needs to be replaced in case of damage,OttawaQuotation slurry pump, swelling and deformation, insufficient spring pressure, breakage, etc.　　Rate loss, so shaft power = effective power + lost power.

　　When using the sand pump, be sure to pay attention to the steering divergence between the motor and the pump. The sand pump has an arrow on the pump to mark the main steering. After the power supply is connected, run the pump without load. Check whether the motor operates normally. During operation, be careful not to exceed the bearing on the pump support to avoidHow much is it,　　When this type of pump is used at ordinary times, the pump and motor operate in a coaxial whole. When it runs, the motor shaft will drive the impeller of the pump to rotate, and then at this time, the rotating force can be brought to the medium, so that　　The treatment methods are as follows: Check whether the current and voltage of the water pump are abnormal at this time. If the current is obviously reduced, for example, it is only half or a little more than normal, it may be that the impeller is worn or the check valve is blocked. If the current is not much different from the normal current, it can be　　There is a difference between submersible slurry pump and sewage pump. Although the media conveyed by the two are not pure water and other media, the difference between slag slurry and sewage is still large. Let&#;s take a look at the difference between the two.Ottawa,OttawaSubmersible sewage pump,　　The balance ring is also disassembled; Then remove the last stage impeller and the key back, remove the impellers, middle sections and guide vanes at other levels in the same way until the submerged slag slurry　　When the submersible slurry pump works, the pump needs to be placed on land, the suction pipe needs to be placed in water, and the pump needs to be started. Due to special structural requirements, when the slurry pump motor is submerged in the water, the slurry pump and submerged slurry circulating pump need to be placed above the water surface, the smaller the allowable cutting amount of impeller diameter. In addition to the sealing effect otherwise the motor will fall into the water　　The higher the specific speed of submersible slurry pump, the auxiliary impeller of the submersible slurry pump can also reduce the axial force.