Odense4-ton cargo elevatorDemonstration of the manufacturing process

Walking: assisted self-propelled, two-wheel traction, self-driving, and car modified.Check the limit switch to see if all the limit switches are loose. If so, please tighten them. Pay special attention to the ultra-high protection stroke of the hydraulic lifting platform to avoid accidents caused by the equipment exceeding the high safety height; check the pins (ear pins and center pins) Check whether the nuts nuts, etc. are loose screws, if any, should be reinforced immediately; ensure that the hydraulic lifting platform rises and falls smoothly; outriggers (for high-altitude operating platform)Odense,Overview of the development of scissor-type aerial work platforms: The use of aerial work platforms originated in North America in the s. Products similar to the current vehicle-mounted aerial work platforms began to be used in North American farms for fruit picking and tree branch pruning.Always check all wires and cables for damage. The damaged part should be bandaged and replaced in time.RockinghamThe hydraulic lifting platform can be divided into: four-wheel mobile type, two-wheel traction type, car modified type, car type, and the lifting height ranges from a meter to s meter.Check the limit switch to see if all the limit switches are loose. If so, please tighten them. Pay special attention to the ultra-high protection stroke of the hydraulic lifting platform to avoid accidents caused by the equipment exceeding the high safety height; check the pins (ear pins and center pins) Check whether the nuts, screws, if any, should be reinforced immediately; ensure that the hydraulic lifting platform rises and falls smoothly; outriggers (for high-altitude operating platform)Unscrew the screw on the dust-proof hole outside the flange of the elevator, adjust the PCS system ring to align the side hole with the dust-proof hole, and tighten the inner hexagon. After that, remove the motor shaft key.

Nowadays, small and medium-sized enterprises are holding products with the idea of ​​good quality and favorable price.The lifting platform has been inspected and debugged before leaving the factory, and all technical indicators meet the design requirements. When using it, it only needs to be connected to the power supply, and the hydraulic and electrical systems basically do not need to be adjusted. Our company is engaged in all kinds of materials such as elevator factories all the year round, remote control system, P IC system.Free consultation,Goods should be stacked on the platform and not tilted. When the freight elevator goes up and down beyond the range of the platform, no one should stand around to watch.It is strictly forbidden to switch the electric control switch with wet hands. Many people tend to ignore this detail. Although the safety voltage of the hydraulic lifting platform is below V, if you touch the power supply with your hands, it may cause lifting failure in light cases,OdenseFactory lift cargo elevator, or electric shock accidents in severe cases.The load of this series of products is divided into . to . tons, and can also be customized according to user requirements, with a load of up to tons.

Conscientiously write the special construction plan for installation and construction, and make safety technical disclosures to the installers.assets,The cleanliness of the hydraulic station is an important aspect of the elevator hydraulic station, so it should not be careless. Moreover, from a professional point of view, there are relevant rules and requirements, and you should refer to the specification manual, so that you can have a correct understanding and know how to achieve better cleanliness.The multi-column aluminum alloy lifting platform is widely used in airports, high-speed rail stations, shopping malls and star hotels for cleaning and circuit maintenance on the top floors of halls. It has high elevation, low weight, flexible movement and simple design.Are the water cooling and air cooling of the hydraulic station the same?Odense,It is best not to cover the aerial work vehicle and park the vehicle outside. If it is windy and rainy, the clothing will repeatedly slap the car paint, especially if the car blows sand on the clothes,OdenseCargo elevator, it will draw many fine scratches on it. Because it will turn black over time. In addition, when the wind does not directly spray powder or clean the sand on the mechanism, but it should be washed with water,OdenseThe cargo elevator is, and prevent the sand particles on the paint surface from being scratched by the vacuum cleaner.Precautions for using guide rail elevators Precautions for using guide rail elevators: It is strictly forbidden to overload, transport flammable and explosive products and other products.Mechanisms: Mechanisms such as tabletops, track grooves, wire ropes, chains, and pulleys are made of solid materials to ensure safety.