Pokhov4 galvanized square pipeSealing principle and structural characteristics of

petrochemical industry

Main uses of square tube: square tube is mainly used in tap water engineering, chemical industry, electric power industry, agricultural irrigation and urban construction. It is one of the key products developed.The characteristics of square pipe are as follows: the production process of square pipe is simple, the production efficiency is high, the cost is low and the development is fast. The strength of spiral square pipe is generally higher than that of straight seam square pipe. It can produce square pipe with larger pipe diameter with narrow blank, and square pipe with different pipe diameter with blank of the same width. However, compared with straight seam pipe of the same length, the weld length is increased by ~, which will be oriented to the whole country for a long time Individuals and enterprises provide all kinds of square tubes, square rectangular tubes, seamless square tubes, galvanized square tubes, galvanized tubes, on-site settlement, honest operation local offices, long-term cooperation, and low production speed. Therefore, most of the smaller square tubes adopt straight seam welding, and most of the large-diameter square tubes adopt spiral welding.Pokhov,Galvanized qb square pipe for low pressure fluid transmission, Standard No.: gbt-. The representative materials are the same as above. It is mainly used to transport low-pressure fluids such as water, gas, air and oil and add water or steam. The surface of square pipe shall be hot galvanized or cold galvanized.Brinell hardness (HB), Rockwell hardness (HRC) and Vickers hardness (HV) are commonly used.Penal,The other is designed with deformation angle, which can be regarded as DEG from round tube to square tube; To & deg; The bending deformation of angle, so the deformation angle & theta; It can accurately reflect the deformation degree of corners and edges. In the design process, considering the influence of dimensional accuracy and metal work hardening, the distribution of deformation angle is usually larger at the beginning and middle passes, and then gradually decreases. In the pass formed directly by arc intersection, the fillet part of the pipe blank cannot be filled with the pass, so the pass perimeter is different from that of the pipe blank. In order to ensure the dimensional accuracy, the fillet part of the pass needs to be corrected and calculated. Therefore, this method has higher design accuracy than other methods. However, due to the large amount of iterative calculation, this method is more suitable for pass design by computer. If you use a frame that deforms both horizontally and vertically, you can directly use the deformation angle & theta; Pass design.When storing QB square pipe, we need to select a suitable place. We need to think about many external factors, such as the corrosivity of steel pipe, etc. Therefore, the place must be clean, dry and ventilated, where harmful gases appear, QB square pipe can not appear, weeds and other sundries should be removed in time, and the outer surface of steel should be kept clean. If there are acid, alkali, salt, it is easy to react with the steel pipe and corrode the steel pipe, if we can think about those higher metal products, we can put them into the warehouse for very good retention. According to geographical conditions, but the ventilation setting is excellent. The difference between QB square tube and seamless steel tube QB square tube is a kind of high-precision steel tube material after cold drawing or hot rolling treatment. QB square tube is mainly used to produce products of pneumatic or hydraulic components, which can be seamless pipe or welded pipe, because there is no oxide layer on the inner and outer walls of QB square tube, no deformation under high pressure, high precision, cold bending, flaring and flattening without cracks. The chemical composition of QB square tube includes carbon silicon Si, manganese Mn, sulfur s, phosphorus P and chromium CR.The principle of straightening machine is that a disc is divided into two sides to clamp round steel straight lines. Professional square tube, square rectangular tube, seamless square tube, galvanized square tube, galvanized tube, high price, service, on-site settlement, honest operation! The edge is one with radius r, and the other outer edge must be two equal diameters with radius R. The diameter of the reinforcement to be straightened is D, and the center distance between them is adjusted to R + R + D.

According to smelting classification and furnace type, A. open hearth steel: (a) acid open hearth steel; (b) Alkaline open hearth steel.The square tube can be sprayed with fluorocarbon paint, which needs some treatment before spraying.Strength refers to the performance of metal materials under static load (excessive plastic deformation or fracture). Since the action modes of load include tension, compression, bending and shear, the strength is also divided into tensile strength, compressive strength, flexural strength and shear strength. There is often a certain between various strengths. Generally, tensile strength is used as the basic strength indicator. Appropriate sites and warehouses shall be selected. The sites or warehouses for storing steel pipes shall be in clean and unobstructed places, away from factories and mines that produce harmful gas or dust. Weeds and sundries shall be removed on the site to keep the steel pipe clean; In the warehouse, it is not allowed to stack with acid, alkali, salt, cement and other materials that are corrosive to the steel pipe. Different types of steel pipes shall be stacked separately to prevent confusion and corrosion; Large section steel, rail, steel plate, large-diameter steel pipe, forging, etc. can be stacked in the open air; Small and medium-sized section steel, wire rod, reinforcement, medium diameter steel pipe, steel wire and steel wire rope can be stored in a well ventilated shed, but they must be covered and padded; Some small steel pipes steel sheets, steel strips, or thin-walled steel pipes, and generally adopts ordinary closed warehouse, that is, the warehouse with roof, close and damp proof in rainy days tight doors and windows and ventilation devices; The warehouse is required to pay attention to ventilation in sunny days, and often maintain a suitable storage environment. The principle of reasonable stacking and first in first stacking is to stack according to varieties and specifications under the condition of stable stacking and ensuring safety. Materials of different varieties shall be stacked separately to prevent confusion and mutual corrosion; It is forbidden to store articles that have corrosive effect on steel pipes near the stacking position; The bottom of the stack shall be padded high, firm and flat to prevent the material from moisture or deformation; The same kind of materials shall be stacked according to the warehousing order, so as to facilitate the implementation of the principle of first in, first out; The section steel stacked in the open air must be provided with wooden mats or strip stones. The stacking surface is slightly inclined to facilitate drainage. Pay attention to the straightness of the material placement to prevent bending and deformation; The stacking height shall not exceed m for manual operation, and m for stacking width; A fixed channel shall be reserved between stacks, generally .m, and the access channel is generally ~ om depending on the size of materials and transportation machinery; The bottom of the stack shall be padded up. If the warehouse is cement floor, it can be padded up by .M; If it is muddy ground, it must be padded . ~ .m high. If it is an open site, the cement ground shall be padded with O & middot; ～O· m, the angle steel and channel steel shall be stacked in the open air, i.e. the mouth shall face down, and the I-beam shall be placed vertically. The i-groove surface of the steel pipe shall not face up to avoid ponding and rust. The packaging and protective layer of the protective materials shall be coated with agent or other plating and packaging before leaving the factory, which is an important measure to prevent material corrosion. Attention shall be paid to protection during transportation, loading and unloading and shall not be damaged, The storage period of materials can be extended the warehouse shall be kept clean and the maintenance of materials shall be strengthened. Before warehousing, materials shall be prevented from being drenched or mixed with impurities. Materials that have been drenched or contaminated shall be wiped according to their properties, such as steel wire brush for high hardness and cloth, cotton and other materials for low hardness; The materials shall be regularly after warehousing. If there is corrosion, the corrosion layer shall be removed; Generally, but for high-quality steel alloy steel sheet, thin-walled pipe, alloy steel pipe, etc., the internal and external surfaces need to be coated with anti rust oil before storage; Steel pipes with serious corrosion shall not be kept for a long time after rust removal and shall be used as soon as possible. With the development of economy, all kinds of square tubes, rectangular tubes, seamless square tubes, galvanized square tubes and galvanized tubes have been recognized by the majority of customers for a long time. There are more and more counterfeit products on the market. In order to prevent being deceived when you are in square tubes, you need to know some knowledge about how to judge the authenticity of square tubes: & ldquo; We can judge by observing the surface and flatness of the square tube. If the surface of the square tube is relatively flat, it can reflect that the square tube is good. On the contrary, if the surface is not goodStatistics,Functional index analysis of qb square tube - mechanical function of plastic square tube. Solid bending, as the name suggests, is to compact the bending. During real bending, the inner and outer rollers and the inner and outer walls of the pipe blank are compacted in both directions.Special performance steel: A. stainless and acid resistant steel; b. Heat resistant steel: including oxidation resistant steel, heat strength steel and air valve steel; c. Electric heating alloy steel; d. Wear resistant steel; e. Low temperature steel; f. Electrical steel.Product description of square tube square tube is a light thin-walled steel tube with hollow square section, also known as steel cold-formed profile. It is a section steel with square section shape and size, which is made of Q hot-rolled or cold-rolled strip or coil as the base material, cold bending and high-frequency welding. In addition to wall thickness thickening the corner size and edge flatness of hot-rolled special square pipe reach or even exceed the level of resistance welding cold-formed square pipe. Good comprehensive mechanical properties, weldability cold and hot workability and corrosion resistance, and good low temperature toughness.

Square pipe welding is suitable for surface treatment of materials. Square pipe welding can be used for ceramic ceramic, metal ceramic and metal metal welding.Promise and keep promise,Engaged in square tube,PokhovHow much is galvanized square tube 110, square rectangular tube, seamless square tube galvanized square tube, galvanized tube, old brand, price advantage and quality guarantee! However, the Demander shall cut off the interface pipe when using it. The weight of short length and non fixed length products shall not exceed % of the total delivery. For qb square pipe with theoretical weight greater than kgm, it shall not exceed % of the total delivery. The bending degree of qb square pipe shall not be greater than mm per meter,PokhovDN50 galvanized pipe,PokhovPrice list per ton of galvanized square pipe, and the total bending degree shall not be greater than .% of the total length. Galvanized qb square pipe for low-pressure fluid transmission, with standard number of gbt-. Representative materials: QA, qbqb, etc. It is mainly used for conveying water, gas, air, oil and heating hot water or steam, and its purpose is limited to general low pressure fluid.First, remove the deposits on the surface of the square pipe surface with copper wire brush. Use the perfume oil or other scrubbing oil on the surface layer, or use phosphate or chromate solution, brush, spray or dip coating. After the fixed reaction time, rinse the acid solution with plenty of fresh water on the surface.The technology of floating mandrel and square tube is gradually mature.Pokhov,Square tube plays an important role in the rapid economic development. The functions of square tube are different, and its characteristics are also different. Square tube has strict standards. There are many welding processes and advantages of square tube. Let me show you the welding process and advantages of lower tube.Mechanical engineering, power plants, agricultural and chemical machinery, glass curtain walls, automobile chassis airports, boiler construction, highway railings, housing construction, pressure vessels, oil storage tanks, bridges, power station equipment, heavy transportation machinery and other welded structural parts with high load, etc. Process classification: according to the production process, square tubes are divided into hot-rolled seamless square tubes, cold drawn seamless square tubes, seamless square tubes and qb square tubes.At this time, if the welding wire of the same material is used for spot welding where the thickness is insufficient, it shall be welded to the fixed thickness, ground and sandblasted, and repair welding shall be adopted where there are cracks, even if the steel pipe with another large opening can be made up at one time.