SokaRubber lining submerged slurry pumpOffice property enters the stock market

　　 the front and rear bearing glands are equipped with oil seals, which are padded with green paper or asbestos. There is a gap of .- mm between the rear gland and the bearing.　　It is occasionally found that there is insufficient liquid supply when using, so what are the reasons for this situation and how to deal with it.Soka,　　 Disassembly of water pump: use a disassembly wrench to remove the water inlet joint by left rotation, and use a disassembly cylinder to impact the conical sleeve at the lower part of the pump. After the impeller is loose, take out the impeller, and remove the guide housing. In this way,SokaSubmersible non clogging sewage pump, the impeller, guide housing, upper guide housing, check valve, etc. are unloaded in turn.　　Normal operation. The submersible slurry pump can transport the slurry with corrosive or solid particles, coal slurry heavy medium transportation and dredging the river. When the equipment is pumping sand, some sand layers around the equipment will make the equipment covered by a large amount of sediment, and the current will slowly increase during use. Well, we should chooseLilongui,　　Adjustment. When using the submersible slurry pump, which will cause equipment problems and affect work efficiency. So we&#;re using　　 determination of model: for water pump or pump with physical and chemical medium similar to water, it is necessary to go to the relevant product catalog or sample, and make correction according to the performance table or performance curve of the model to see whether the normal working point falls in the priority working area of the pump.　　Flexibility. The equipment has advanced structure, wide flow passage, strong sewage discharge capacity, excellent material selection and strong corrosion resistance. It is suitable for conveying liquids containing solid particles, such as sandstone,SokaScrew deep well pump, cinder and tailings. So what are the requirements for its work? Let&#;s understand briefly.

　　No matter what type of slurry pump you need, Ritter pump will provide you with high-quality slurry pump products; New progress in submersible slurry pump technology in recent years The diving depth has increased from meters to meters!　　Solution: Please perform parameter initialization (item F and re edit the parameter (possible cause: there is a conflict between item F and item f　　.Executive standard, resulting in poor heat dissipation effect.　　The installation of submersible slurry pump is a step that needs to be concerned. Since we all care about it, it is mainly because the installation will directly affect the use effect. The installation work should be seamless. Some key operating points can be seen when installing the slurry pump.　　Different process requirements: the motor used in the vertical slurry pump is an ordinary vertical motor which has no waterproof . The motor of the submersible slurry pump and the pump shaft are coaxial. The motor shall be waterproof and sealed. The motor and the pump body can invade underwater at the same time.

　　 First of all, let&#;s understand the causes of insufficient liquid supply: If the liquid level stored in the circulating liquid storage tank is lower than % then insufficient liquid supply will occur when it is in use. Or the pump adds too much lubricating oil,　　Where ρ—— Density of transmission medium liquid (kg/m; γ—— Gravity of medium liquid (n/m; H -- pump lift (m); Q - water pump flow (m/s); G - gravitational acceleration (m/s.　　The difference between the shaft power P and the effective power PE is the power loss in the pump which leads to accumulationManagement Department, which is measured by the pump efficiency. The pump efficiency is the ratio of the effective power and the shaft power, which is measured by η Indicates.　　For the pipeline pump in the workshop, it is necessary to consider whether the pipeline pump is worn to a certain extent due to inadequate maintenance, but the performance of the pipeline pump is degraded. In case of abnormal water absorption during installation, check the motor during installation, and check the motor wiring and speed,　　Analysis of installation problems of slurry pump For bearings lubricated with thin oil, oil shall be added according to the oil level line of the oil standard before start-up. Add (HL hydraulic oil in winter and (hl hydraulic oil in summer. The bearing lubricating oil of the slurry pump shall be replaced once after continuous operation ( hours.Soka,　　In this way, a smooth surface can be formed on the surface.　　 the water pipe shall be provided with a gate valve to regulate the pump working point. The valve shall be installed as close to the pump outlet as possible. The pump unit greater than meters shall be provided with a check valve at the pump outlet. In case of sudden shutdown,SokaDrilling fluid slurry pump, it is necessary to prevent damage to flow passage components caused by water hammer.　　For example, concentrate and tailings are treated in the concentrator, ash and slag are removed from the power plant, slime and dense medium coal are transported in the coal preparation plant, and slurry is transported in coastal river mining operations. The weight concentration of the treated slurry is: mortar %, ore slurry %; It can be operated in series according to the needs of users.