GaopingCan hydraulic pressure automatically lift and lowerWhat are the survival rules of the industry

Remove and disassemble the hydraulic lift cargo elevator lowering valve, blow out the plunger with compressed air, then install it and reinstall it.Take mobile elevators for example, the same goes for them. Of course, during the internship, there may still be some questions about the elevator, but without contact, simply mastering some specific skills can effectively handle these questions.Gaoping,Any machinery needs to be maintained after use, let alone large machinery. Poor maintenance of elevators after use can reduce the lifespan of elevators. Today, the editor will tell you how to maintain elevators after use. In order to maintain the good technical condition of elevator machinery,GaopingMovable hydraulic lifting platform, extend the service life of equipment, and reduce mechanical failures, construction enterprises must maintain according to the relevant regulations According to maintenance regulations, necessary equipment maintenance work should be carried out. It is not allowed to focus solely on the use and maintenance of the equipment. It is strictly prohibited for equipment to be taken out of warranty or repair.When using, the four legs should be firmly supported on a solid ground (based on the walking wheel about to leave the ground), and sleepers can be used when necessary.Shuto Orizari,Although lifting cargo elevators have good safety, in practical work, if we do not pay attention to detailed maintenance, accidents may occur. Therefore, we should pay attention to them when performing daily maintenance.There are problems with the hydraulic torque converter and compensation system of mobile elevators, such as weak torque converter, power shift failure, high oil temperature, insufficient hydraulic torque converter, inadequate pressure adjustment insufficient back pressure. Check the quality of torque converter oil (whether hydraulic transmission oil is misused), dosage, torque converter pressure regulating valve back pressure valve and their set pressure value. Power shift failure. Quick return valve, pressure reducing valve, power transmission valve The directional valve is stuck or leaking internally. Oil pollution is severe. Check the cause of the valve sticking and eliminate it accordingly. Filter or replace the hydraulic oil. If the oil temperature rises too much, check if there is any problem with the cooler. Check the quality of the hydraulic oil. The brand hydraulic boarding bridge, also known as the hydraulic loading and unloading platform, can achieve rapid loading and unloading of goods. The structure design is simple, the use is flexible and convenient, and the work efficiency is high. It is widely used and widely popularized in the market.Regular inspection and maintenance, eliminating hidden dangers, and troubleshooting are beneficial for improving work efficiency, extending equipment service life, and ensuring the safety performance of elevators.

Staying below high-altitude work sites is prohibited, and safety nets or other protective devices should be installed below the work site to avoid injury from falling objects.How to use a hydraulic elevator and whether the emergency stop device is effective is very important during use. If special circumstances arise, the emergency stop can be used. Therefore, before use it is necessary to carefully check whether all items are normal and ensure the effectiveness of the braking device.No matter what problem occurs,Gaoping3-meter hydraulic lifting platform, if encountering an unsolvable problem with a hydraulic lifting platform, it is better to produce it quickly and conveniently, and guide the manufacturer to solve it. Please pay attention to safety precautions during maintenance.property rightLoose motor fixing screws: When the motor fan rotates, there is a sound. If the screws fixing the motor are loose, the motor collides with other components, resulting in a sound; The joints of each pin shaft are dry lacking oil, and there is hard friction between the iron parts, which not only damages the components but also produces abnormal noises. Therefore, the editor should emphasize again that timely maintenance and frequent refueling are important; If the hydraulic lifting platform does not rise, there is air in the hydraulic oil. You can open the exhaust hole, add gas, and then tighten it again; Hydraulic oil solidification: replace the hydraulic oil; Oil leakage: Check if there is any oil leakage at the interfaces of each oil pipe. If there is any oil leakage, replace it in a timely manner; Motor reversal: Check for wiring errors; (Manufacturers of hydraulic lifting platforms who do not understand electricity in a timely manner)Each department's electric brush should be kept clean, and the brush pressure should be adjusted to ensure that its area is not less than %In our daily life, hydraulic cargo elevators are increasingly widely used and loved by customers. As a lifting tool, the editor will introduce the daily maintenance of hydraulic cargo elevators.

Check the rollers, intermediate shafts, and bearings; Oil cylinder pin and bearing; Equality and wear of the hinge shaft and bearings of the boom; Add oil to the above components for maintenance of outdoor elevators and factory elevators. Extend the service life of bearings.Process inspection,The application scenarios of mobile elevators may require several or even dozens of passenger elevators in some office buildings and hospitals. In order to increase the speed, efficiency, and usable area of electric elevators, with each group responsible for a portion of the floors, and make different adjustments and scheduling based on the usage mode of different floors at different times.What kind of function can be achieved by installing the elevator? Before installation, confirm whether the motor and elevator are intact, and strictly check whether the dimensions of each part connected to the motor and elevator match. Here are the dimensions and fit tolerances of the positioning boss, input shaft, and elevator groove of the motor.Hydraulic boarding axle; Streamline” The open hinge joint design increases the welding area by more than three times compared to ordinary tubular joints, effectively extending the service life and simplifying maintenance.Gaoping,Although lifting cargo elevators have good safety, in practical work, if we do not pay attention to detailed maintenance, accidents may occur. Therefore,GaopingScissor fork hydraulic lifting platform, we should pay attention to them when performing daily maintenance.Improper use of oil: Inadequate maintenance of high-altitude work platform equipment such as mobile elevators can also lead to small fitting gaps of components, making it difficult for oil to form a uniform oil film on the friction surface. Additionally, due to assembly and other reasons, it is difficult to ensure the uniformity of fitting gaps, thereby reducing efficiency and causing early abnormal wear of equipment components; In severe cases, it may cause scratches or bite on the friction surface of precision fitting, leading to the occurrence of abnormal equipment noise.What are the advantages of installing a guide rail type elevator for goods? The advantages of civil engineering are easy to install: there is no need for a machine room above the shaft, and the top layer can be installed at a height of more than meters. The computer room can be located within a radius of meters of the shaft, occupying an area of only - square meters. The hydraulic elevator is not equipped with a counterweight device to improve the utilization rate of the shaft area. The load and load cylinder of the hydraulic elevator directly act on the foundation pit