Loyo45 large diameter seamless pipeThe market is still optimistic

The flange of H-beam is of equal thickness, including rolling section and combined section composed of three plates welded. All I-beams are rolled sections. Due to poor production technology, the inner edge of the flange has a slope of : The rolling of H-beam is different from that of ordinary I-beam. Only one set of horizontal rolls is used. Because its flange is wide and has no inclination (or the inclination is very small), a group of vertical rolls must be added for rolling at the same time. Therefore, which exceeds the welded composite section.Application characteristics of I-beamLoyo, Spiral seam high-frequency welded steel pipe (sy- for general low-pressure fluid transportation takes hot-rolled steel strip coil as pipe blank and is often spiral formed at warm temperature. High frequency lap welding method is selected for welding spiral seam high-frequency welded steel pipe for general low-pressure fluid transportation.Plan option : Martensitic chromium alloy pipe,Traun,As shown in the name, I-beam is an I-shaped section steel. The inner surface of the upper and lower flanges has an inclination, generally :, which makes the outer flange thin and the inner flange thick. Therefore, the section characteristics of I-beam in the two main planes are very different, and it is difficult to give full play to the strength characteristics in application. Although the thickened I-beam has also appeared in the I-beam market, the structure of the I-beam has determined its torsional performance.The general alloy pipe with improved performance is variable and has high application value. The alloy pipe contains more Cr and is heat resistant Low temperature resistance Corrosion resistance. There is no aluminum alloy in plain carbon seamless steel pipe, not very little aluminum alloy, and the alloy pipe is used in crude oil Aerospace Chemical plant Power engineering heating furnace. Because the physical properties of alloy tubes are easy to change and adjust.The production process can be summarized as follows: pre leveling → finishing → straightening → post leveling. Flat steel / A / B steel with width of -, thickness of -, rectangular section and slightly pure edge. Flat steel can be finished steel or it can be used as blank for welded pipe and thin slab for laminated thin plate.

The working principle of flat steel finishing machine in I-beam production process is to pre level and finally level the cold flat steel with two groups of leveling wheel sets staggered up and down in the thickness direction; A pair of finishing wheels arranged relatively are used to extrude the width direction, and the compression amount is adjustable; Straighten the width with staggered straightening wheels. Chromium can improve the hardenability and wear resistance of steel so that the width is compressed to achieve the expected parameters, and improve the corrosion resistance and oxidation resistance of steelAccording to the national standard of hot rolled H-section steel in China (GB / t-, H-section steel is divided into narrow flange, wide flange and steel pile, whose codes are Hz,LoyoQ345 straight seam welded pipe, HK and Hu respectively. Narrow flange H-section steel is suitable for beams or compression bending members, while wide flange H-section steel and H-section steel piles are suitable for axial compression members or compression bending members. Compared with H-section steel, IX and iy are not as good as H-section steel under the premise of equal weight.Quality department, Hot push hole diameter. More sensitive applications and facilities of such methods require simplicity, low cost, easy maintenance, durable economic development and convenient product specification transformation. For example, the production of large diameter must be grooved pipe, elbow and similar products. You only need to add some spare parts. The expansion method of hot push can be used to process and manufacture large-diameter, thick wall and thin alloy steel pipes, curtain wall engineering, mechanical equipment and vehicle manufacturing.I-beam is mainly used in building structure curtain wall engineering, mechanical equipment and vehicle manufacturing.

I-beam: national standard * what is the wall thickness of I-beamanalysis,LoyoReinforcement turnover software stand-alone version,→ under the same section load, the weight of hot-rolled H steel structure is reduced by % - % compared with the traditional structure.Installation of galvanized pipe and precautionsXhy- series high hardness alloy I-beam; Undertake drawings and process wear-resistant pipes（ Φ ≥mm）； Undertake the processing and production of vulnerable parts of cement machinery; Welding technology consultation and service; The wear-resistant layer of alloy wear-resistant plate of high chromium heap welding flux cored wire series is mainly high chromium, as well as manganese,LoyoPrice of reinforcement sleeve, molybdenum, niobium, francium and other components. The alloy carbide formed has strong stability at high temperature.Loyo,Passivation treatment operation of alloy pipeH-shaped steel groove is deep and thick, and can withstand forces in two directions. Cold extrusion. This kind of processing method is more purposeful. Before the preparation of steel processing and extrusion molding, when the extrusion molding is used for mm diameter pipe fittings, the investment of machinery and equipment is less, so the raw material consumption is also very small, and the technology is relatively perfect. Once the tube size is increased, the cold extrusion method must have large cargo capacity and high-power machinery and equipment. Therefore, the automatic control system will be upgraded.