St. Javier15CrMo high pressure alloy pipeAdjust industry process parameters

Aiming at the connective tissue and texture produced in stainless steel plate Position and other crystal defects are generally removed by heat treatment processes such as quenching or quenching. The effect of quenching is to optimize the crystal eliminate structural defects, reduce strength, improve plastic deformation, and also conducive to cold drawing. In the production and manufacture of cold drawn alloy pipe, quenching machinery and equipment cannot be lacked. Therefore, the formulation of appropriate annealing process is a necessary condition to ensure that the alloy pipe mechanism meets the standard and the commodity does not crack. If the manufacturer in order to better one sidedness, reduce the product cost and reduce the quenching process, it will eventually lead to bad harm to the product quality. The defects can be removed by grinding with sand wheel, but the remaining wall thickness must be within the allowable standard.St. Javier,The fifth is the welding environment control to ensure that the temperature, humidity and wind speed during welding meet the process requirements.So why is the alloy pipe easy to rust after being pickled and passivated by the software?Iskenderun,C-section steel has uniform zinc layer, smooth surface,St. JavierHow much is 160 I-beam per ton, no zinc scar, no zinc leakage and high dimensional accuracy. All surfaces are wrapped by zinc layer, and the zinc content on the surface is usually -g /? It has long service life, corrosion resistance and durability. It is a kind of stronger protection.Plan scheme : high carbon steel with carbon content exceeding .% and alloy pipe with chromium content not less than %I-beam is a long strip steel with groove section, which belongs to carbon structural steel for construction and machinery. It is a section steel with complex section, and its section shape is groove shape. China&#;s imports of I-beams are greater than its exports. The main producing areas are Tangshan Iron and steel, Baotou Iron and steel, Shangang, huangte, Xuanhua Iron and steel, Japan iron and steel, double convex steel pipe, double concave steel pipe, melon seed steel pipe, conical steel pipe, corrugated steel pipe, watch case steel pipe and others.→ compared with general section steel, it has the advantages of low cost, high precision and small residual stress. It does not need expensive welding materials and weld detection, and saves about % of the manufacturing cost of steel structure.Inspection environment,The pickling agent in the pickling process contains many acidic substances, including hydrochloric acid,St. JavierSteel bar cutter type 50, sodium cyanide etc., which has strong corrosion and reduction and the temperature of etching substances is relatively high. Therefore, the corrosion resistance of alloy pipes is specified higher.Function of I-beam: where is I-beam mainly used?H-section steel is an economic section high-efficiency profile with more optimized section area distribution and more reasonable strength weight ratio. It is named because its section is the same as the English letter 'H'. There is no slope on the inner side of the two outer edges of H-section steel, which is straight. This makes the welding and splicing of H-section steel simpler than I-section steel, better mechanical properties per unit weight, and can save a lot of materials and construction time.

Alloy pipes can be used for heating (cooling) projects.Statistics, Judged as failing.Galvanized pipe is actually galvanized pipe. This is mainly because it increases the corrosion resistance of the steel pipe, so it is evenly coated with a layer of zinc. It can prevent the erosion of other chemicals such as and steam, and protect the steel strip. It is non-destructive and effectively prolongs its service life. Generally, the steel strip purchased is rolled into a large number by the galvanized pipe manufacturer, so pay attention to it during storage.I-beam is mainly divided into ordinary I-beam, light I-beam and wide flange I-beam. According to the height ratio of flange to web, it is divided into wide, medium and narrow flange I-beams. The specifications of the first two are -, that is, the corresponding height is -. At the same height,St. JavierHow much is the wholesale price of welded pipe, the light I-beam has narrow flange thin web and light weight. Wide flange I-beam, also known as H-beam, is characterized by two parallel legs and no inclination on the inner side of the legs. It belongs to economic section steel and is rolled on four high universal mill, so it is also called 'universal I-beam'. Ordinary I-beam and light I-beam have formed national standards.St. Javier,Using alloy pipe to produce ring parts can improve the utilization rate of raw materials, simplify the production and manufacturing process, and save raw materials and production and processing construction time, such as roller bearing ring throwing Nowadays, seamless steel pipe has been widely used to produce hydraulic jack sleeve.Alloy pipe is a spiral seam seamless steel pipe, which is made of hot-rolled strip steel coil, often processed by warm extrusion and welded by automatic double wire double side arc welding process. The alloy pipe sends the hot-rolled strip steel to the welded pipe unit, and the hot-rolled strip steel is extruded through multiple passes. The hot-rolled strip steel is rolled slowly to produce annular pipe material with open mouth gap. Adjust the reduction amount of the extrusion roll to control the welding gap at ~ mm and make both sides of the weld flush. Cross rolling pass system. This pass system refers to that the two open legs of the I-beam pass are not on the same side of the waist at the same time, and the waist has an included angle with the horizontal axis.