NingxiaMobile hydraulic lifting platformOperation warning instructions

The inconsistent rotation axis of the support rod in the middle of the hydraulic lifting platform results in the lifting platform being unable to function properly, causing serious damage to the platform and causing the table to tilt. Please carefully check that the general shear type high-altitude work platform was not strictly tested for tilt before leaving the factory, and was put into the market causing many accidents. For small enterprises, they are not very concerned about this aspect of tilt detection, This is also why there are such a large number of lifting equipment with this problem. The problems with the oil cylinder and power unit system are often due to insufficient power and substandard oil cylinder quality, which are also very important issues for enterprises themselves.At this point, if the high-altitude work platform is overloaded, it may cause damage to the components and cause some mechanical failures.Ningxia,Common problems and specific solutions during the operation of hydraulic boarding bridges: motor phase loss (motor does not move and there is a buzzing sound)The power unit adjustment, whether it is a scissor type lifting platform or a guide rail type lifting cargo elevator, is composed of the power unit and the oil cylinder. The power unit has four outlets during production, which can be adjusted to increase or decrease the hydraulic oil flow rate of the oil cylinder. We can adjust the motor speed or the electro-hydraulic proportional valve to adjust the hydraulic oil flow rate; What factors will affect the lifting speed of hydraulic elevators? The longer the hydraulic oil pipe the longer the lifting time. Therefore, during installation, the length of the oil pipe should be minimized as much as possible within the allowable range of the design; On the basis of adjusting the power unit, the size of the oil pipeline can also be adjusted, and corresponding adjustments can be made while ensuring that the equipment meets normal demand and safety.Bitung,Carefully prepare a special construction plan for installation and provide technical disclosure to the installation personnel. Our company has been engaged in various types of scissor lift manufacturers and other materials for years, and operates with integrity. Welcome to call!Drain and discard the hydraulic oil from the hydraulic lifting cargo elevator. For the outdoor guide rail elevator, tighten the joint and remove the oil filter. After cleaning, clean it with compressed air, and then return it to the oil tank and connect the pipeline.Remove and disassemble the hydraulic lift cargo elevator lowering valve, blow out the plunger with compressed air, then install it and reinstall it.

The daily maintenance of guide rail type cargo elevators should ensure that the transmission position where the grease nipple is located needs to be lubricated twice a month. For areas where grease cannot be added, it is necessary to clear the oil circuit or replace the grease nipple until butter can be added. Otherwise, it is prohibited to use the equipment.The hydraulic pipeline is probably congested. The hydraulic pipeline is also a particularly important key, checking whether the hydraulic pipeline is smooth. Focus on checking whether there are signs of congestion or jamming in various hydraulic valves, including one-way stop valves, electromagnetic directional valves, proportional control valves, overflow valves, the hydraulic valve should be cleaned or replaced in a timely manner, as the hydraulic oil may deteriorate or contain impurities. After the hydraulic oil is permanently used, there may be impurities or deterioration in the hydraulic oil. Take a sample for inspection to see if it contains fluid particles, discoloration, or odor. If necessary, replace the hydraulic oil.The power unit adjustment, whether it is a scissor type lifting platform or a guide rail type lifting cargo elevator, which can be adjusted to increase or decrease the hydraulic oil flow rate of the oil cylinder. We can adjust the motor speed or the electro-hydraulic proportional valve to adjust the hydraulic oil flow rate; What factors will affect the lifting speed of hydraulic elevators? The longer the hydraulic oil pipe, the longer the lifting time. Therefore, during installation, the length of the oil pipe should be minimized as much as possible within the allowable range of the design; On the basis of adjusting the power unit, the size of the oil pipeline can also be adjusted, and corresponding adjustments can be made while ensuring that the equipment meets normal demand and safety.market price,The inconsistent production dimensions of the hydraulic lifting platform support rods are a quality defect of the lifting platform equipment itself. It is recommended that the manufacturer replace them as the probability of this situation occurring is relatively low.The hydraulic system of the hydraulic boarding bridge has stable performance, high quality, and is sturdy and durable.Although lifting cargo elevators have good safety in practical work, if we do not pay attention to detailed maintenance, accidents may occur. Therefore, we should pay attention to them when performing daily maintenance.

The second is that the steel will have obvious thermal expansion effect at low temperature. Although this property of steel will be taken into account when designing and manufacturing hydraulic elevators, the environment is different after all. Under low conditions, the steel will have some unstable performance,NingxiaLifting platform hydraulic station, toughness decline,NingxiaAluminum alloy hydraulic lifting platform, etc. At this time, more attention should be paid to the maintenance of equipment to keep key parts to avoid dry grinding.Encyclopedic knowledge,Any product always has a break-in period when it is first used, so what precautions should we pay attention to during the break-in period when using a hydraulic lifting platform? Today, the editor will share this topic with everyone.Timely wrapping and replacement of damaged parts is a type of hydraulic elevator, also known as guide rail hydraulic elevator, suitable for transporting goods above buildings, restaurants, and hotel floors. Here is Lipusheng Machinery to introduce the daily maintenance of the elevator.Each department's electric brush should be kept clean, and the brush pressure should be adjusted to ensure that its area is not less than %Ningxia,Loosening: The newly processed and assembled components of high-altitude work platform equipment such as mobile elevators have a tendency to have geometric shapes and matching dimensions. In the early stages of equipment use, due to the influence of alternating loads such as impact and vibration, or factors such as heat and deformation, coupled with rapid wear and tear,NingxiaLifting platform hydraulic pressure, it is easy to cause the previously fastened components of high-altitude work platform equipment such as mobile elevators to become loose.There are foreign objects inside the oil delivery pipe of the hydraulic lifting platform, which can cause uneven force distribution during the delivery of hydraulic oil, resulting in uneven surface conditions. It is recommended to carefully check whether the delivery pipe is smooth.Fault analysis of mobile elevators: Mobile elevators cannot lift or have weak lifting force: overflow valve pressure regulation does not meet the requirements: adjust the pressure to the required value; Oil cylinder internal leakage: check or exchange oil cylinder components; Clamping or internal leakage of directional valve: Check or exchange valve components; If the oil level is too low and the oil inlet filter is blocked, add enough oil and clean the filter. The fuel supply pump has drawbacks: check or exchange the pump.