XigongBooster pipeline pumpObstacles to large domestic sales

　　Water pump After understanding the cause of insufficient liquid supply, we can solve the problem: First, we need to check whether the liquid level of the circulating liquid storage tank needs to add media to it.　　 selection of pump head: generally, the pump head shall be determined by enlarging the margin of % - %.Xigong,　　Eliminate hidden dangers of fire pump in time.　　The submersible slurry pump is a slurry pump which is connected with the motor and works under the water at the same time. Compared with horizontal slurry pump and vertical slurry pump, the biggest advantage is that it is flexible,　　 There is also a vibration method to measure the vibration frequency of the pump, and the measurement is relatively simple. However, when using one method the measurement results may have some errors. When using the submersible slurry pump, there are other vibration sources that will affect the measurement results, so it is actually the main　　Whether the pump is evacuated or overflowed, etc., and handle it at any time.　　The fruit is also bad; When the axial flow pump is used, its water output is relatively large, but the head is not too high, so the effect of using the submersible slurry pump in many plain areas is also relatively good; The water output and head of the mixed flow pump are actually derived from one

　　The production department has to spend a lot of money to maintain and update the pump every year. The pumps made of cast iron, bronze,XigongSubmersible non clogging slurry pump, rubber lining,XigongRubber lining submerged slurry pump, titanium alloy and other materials used in China&#;s mining, chemical and water conservancy projects on the Yellow River are prone to wear, short service life and many faults　　 Improve work efficiency. The traditional manual start-up of fire pump is difficult to operate, complex and dangerous. Manually starting the fire pump can only be operated one by one. If there are a large number of fire pumps, it will take a lot of time, and its work efficiency is extremely low. cf　　Most of the time, we don&#;t know how to choose the pump when we buy it. In fact, we only need to choose the appropriate equipment according to our own use needs when we choose it. It&#;s more like that in a conventional family, when we use it, the flow is smallTotal quality management,　　The above is a brief introduction to the effect and form of shaft seal of submersible slurry pump. Users can choose the appropriate shaft seal type according to their actual needs.　　Now you know the reason why the pump has air turbidity. In fact, this is a very common phenomenon. You don&#;t have to worry about it. Water pump can transport many things, such as water, oil,XigongDeep well submersible pump, liquid metal, acid-base night and so on. It is a good means of transport.　　Work, no noise and vibration, and the site is cleaner.

　　Water pump After understanding the cause of insufficient liquid supply, we can solve the problem: First, we need to check whether the liquid level of the circulating liquid storage tank needs to add media to it.Meticulous workmanship,　　 repair and level the welding part of the submersible slurry pump with a file, clean the part to be bound with alcohol again and wipe it dry.　　(d) The average maximum relative humidity in the wettest month is %. At the same time the monthly average minimum temperature is not higher than ℃　　 in addition, but such measurement will also be affected by the surrounding noise the noise method directly detects the noise of the equipment in the detection process, so in fact, such measurement is not very accurate.Xigong,　　 Precautions for disassembly of submersible slurry pump Before disassembling the filter press, make sure that the liquid in the submersible slurry pump is completely discharged. If the rotor is disassembled, drain the lubricating oil in the rotor bearing housing. If the newly added oil is stored, so the wear resistance of the pipeline should also be considered.　　Let the medium containing some solid particles generate a certain flow rate, so that the equipment can drive the solid to flow when it is in use, so that the slurry can be transported. In terms of the principle of the submersible slurry pump, it is actually quite simple