Winnie snowPrice of hydraulic platform lift truckMain performance parameters

Loose motor fixing screws: When the motor fan rotates, there is a sound. If the screws fixing the motor are loose coupled with the vibration of the motor itself, the motor collides with other components, resulting in a sound; The joints of each pin shaft are dry, lacking oil, and there is hard friction between the iron parts, the editor should emphasize again that timely maintenance and frequent refueling are important; If the hydraulic lifting platform does not rise, there is air in the hydraulic oil. You can open the exhaust hole, add gas, replace it in a timely manner; Motor reversal: Check for wiring errors; (Manufacturers of hydraulic lifting platforms who do not understand electricity in a timely manner)When conducting high-altitude operations on dangerous edges such as roofs, slopes, or cliffs, guardrails or safety nets should be installed on the side facing the air, or safety belts or ropes should be used.Winnie snow,Check the overall structure for any deformation and damage to important components, especially load-bearing support rods, chains, etc.There are three movable plates on both sides of the adjustment plate, which can effectively avoid accidentally injuring the toes of operators when the adjustment plate is lowered, ensuring the safety of equipment use.Lance,The lifting force of the scarifier is not strong or the lifting force is weak: the pressure regulation of the overflow valve does not meet the need to adjust the pressure to the required value; Refer to cleaning item above for leakage in the oil cylinder; The directional valve is stuck or leaking internally; The oil level is too low, and the oil inlet filter is blocked; The fuel supply pump has drawbacks; Check the wear and tear of the one-way valve core and valve seat, and check if the one-way valve spring is tired or deformed.Before using the machine,Winnie snowScissor fork hydraulic lifting platform, the staff should carefully inspect the hydraulic and electrical systems to ensure that there are no leaks or bare leaks before use.Operating cost advantage: Low failure rate. Due to the use of advanced hydraulic systems and good methods,Winnie snow3 ton hydraulic lifting platform, it is driven by the pressure generated by its own weight, which greatly saves energy.

Novice operators: Due to their lack of understanding or lack of understanding of the operation methods of high-altitude work platforms such as mobile elevators, it is easy for them to make mistakes and cause equipment malfunctions. Operators in this area need to patiently learn and pass training before they can operate and use them.Usually, it is necessary to check whether each organization operates normally and whether there is any noise. If any obstacles are found, they must be quickly eliminated.Check the hydraulic oil quality and level. When the lifting platform is raised to a high position, the hydraulic oil level should be - millimeters higher than the bottom of the oil tank. When the color of the hydraulic oil darkens, the oil becomes sticky, or there are foreign objects such as gravel in the oil, the hydraulic oil should be replaced in a timely manner. The hydraulic system of the lifting platform should be checked for hydraulic and pipeline connections. If the pipeline is damaged, it should be replaced immediately; When there is looseness in the connection part, tighten the pipe joint.Marketing Department,Staying below high-altitude work sites is prohibited, and safety nets or other protective devices should be installed below the work site to avoid injury from falling objects.Operating cost advantage: Low failure rate. Due to the use of advanced hydraulic systems and good methods, the failure rate of elevator operation can be minimized. Low power consumption: When the hydraulic elevator descends, it is driven by the pressure generated by its own weight, which greatly saves energy.Are there any damages to the wires and cables of the department. We need to quickly bandage and replace the damaged department.

What should I pay attention to when starting a new mobile elevator? High priced and various specifications of scissor lift manufacturers welcome scrap merchants, industrial companies,Winnie snowAluminum alloy hydraulic lifting platform, enterprises, and power departments to visit and negotiate with the company!Safety and health,The second is that the steel will have obvious thermal expansion effect at low temperature. Although this property of steel will be taken into account when designing and manufacturing hydraulic elevators the environment is different after all. Under low conditions, the steel will have some unstable performance, such as hardness increase, toughness decline, etc. At this time, more attention should be paid to the maintenance of equipment to keep key parts to avoid dry grinding.Hydraulic lifting platforms can be divided into: four wheel mobile, two wheel traction, car modification, car type, auxiliary self-propelled, and lifting heights ranging from a meter to meter.The guide rail type cargo elevator has been inspected and debugged before leaving the factory and all technical indicators have met the design requirements. When in use, and the hydraulic and electrical systems do not need to be adjusted.Winnie snow only the power supply needs to be connected,Are there any damages to the wires and cables of the department. We need to quickly bandage and replace the damaged department.Unique design; Work; The steel frame can withstand average pressure, effectively reducing the torsion of the frame, and has stronger durability.Every month, it should be ensured to add butter twice to the transmission position where the grease nipple is located. For areas where butter cannot be added, it is necessary to clear the oil circuit or replace the grease nipple until butter can be added. Otherwise, it is prohibited to use the equipment.