Yuanbao MouytainMovable hydraulic lifting platformWhat are the selection criteria

When the hydraulic oil of the equipment is insufficient,Yuanbao MouytainHydraulic lifting platform experiment, it will not cause lifting. At this point, you only need to add enough hydraulic oil to run.Hydraulic lifting table: the hydraulic lifting table is widely used in various industrial enterprises and production lines such as automobile, container, mold manufacturing, wood processing, chemical filling, etc., to meet the lifting needs of different operation heights, and can be equipped with various table forms (such as ball, roller, rotary table, steering, tipping, telescoping), and with various ways (separate, linkage, explosion-proof), it has stable and accurate lifting, frequent starting The characteristics of large load capacity effectively solve various lifting and lowering difficulties in industrial enterprises, making production operations smooth.Yuanbao Mouytain, the oil should be replaced regularly to ensure that the additives are effective. The filter can only absorb a limited amount of dirt particles and other impurities from the oil. Replace the filter according to the recommended cycle to keep the system clean.When the hydraulic oil is insufficient, the hydraulic pump will experience suction, causing air to enter the hydraulic oil and producing high noise.Tokyo International Airport,The hydraulic oil used in the system has the same brand, and the oil temperature is between ~ ℃. Use a large flow rate to remove impurities from the system as much as possible. The hydraulic system needs to be cleaned repeatedly three times or more, clean the filter and add new oil after using a new filter element.When disassembling and adjusting the reverse organization of the equipment the system should be drained while the oil is hot. After cleaning, attention should be paid to ensuring that the centerline of the reverse organization reducer is parallel to the centerline of the gear, and its meshing surface is not less than %. The meshing gap should be appropriate.There are many reasons for unstable workbench descent,Yuanbao MouytainDouble fork hydraulic lifting platform, such as overload, unstable support, severe eccentric load, hydraulic oil impurities, etc. In response to the above reasons, it can be solved by reducing the load, adjusting the center of gravity of the load, and replacing hydraulic oil wholesale for hydraulic cargo elevators.

There is air in front of the pilot valve of the elevator overflow valve noise overflow valve. The damping hole on the main valve core of the overflow valve is blocked by oil dirt, and the pilot valve and valve seat are matched without spring deformation or incorrect installation. The remote control port has excessive oil flow, and resonance occurs with components in the circuit. Troubleshooting: Strengthen sealing, repeatedly adjust the pressure, exhaust and clean the valve body several times, repair or replace the spring, replace the oil, and other components. The pressure setting of other components should not be similar to the pressure setting of the relief valve. . The noise of the elevator pipeline is usually caused by excessive dead bends or loose fixed sleeves in the hydraulic pipeline.High altitude work should always use tool bags. Tools with larger boarding bridges should be tied to sturdy components with ropes, and should not be placed randomly to prevent accidents caused by falling from a height.Regularly check all wires and cables for damage. It is necessary to wrap and replace the damaged parts in a timely manner.Quality inspection report,Therefore, in the hydraulic pipeline assembly line, it is necessary to avoid dead bends as much as possible and check the tightness of the sleeve in a timely manner.The cylinder head oil seal is too tight or the rod is bent, which can also cause noise during movement due to other forces. At this point, the oil seal or straightening rod must be replaced in a timely manner.The hydraulic lifting platform often checks the connection status of each part, and if there is any looseness, it should be tightened. The connection bolts of the machine body should be checked for tightness when the elevator body is under pressure (the compression condition can be formed by rotating the arm). All connecting shafts need to have split pins and need to be fully opened.

Regularly check all wires and cables for damage. It is necessary to wrap and replace the damaged parts in a timely manner.Welcome calls When disassembling and adjusting the reverse organization of the equipment, attention should be paid to ensuring that the centerline of the reverse organization reducer is parallel to the centerline of the gear,Yuanbao MouytainHydraulic guide rail lifting platform, and its meshing surface is not less than %. The meshing gap should be appropriate.The so-called input hydraulic energy refers to the input flow rate and pressure, and the output machinery is the speed and traction force during linear motion. All these parameters are achieved through changes in working volume, so hydraulic cylinders are a type of volumetric actuator. In order to meet the different needs of various machinery, hydraulic cylinders have different structures and hydraulic capabilities. According to hydraulic capacity, it can be divided into single acting hydraulic cylinders and double acting hydraulic cylinders. According to its structural characteristics, it can be divided into plunger hydraulic cylinders and hydraulic cylinders. Telescopic hydraulic cylinders and hydraulic cylinders are both referred to as the heart of hydraulic cargo elevators. How to maintain the heart of a hydraulic cargo elevator? Professional elevator manufacturers guarantee quality, service, and quality. Your satisfaction is our pursuit! Welcome to inquire by phoneRemember not to overload, overload is the root cause of many faults.Yuanbao Mouytain,The downward movement of the hydraulic cylinder (i.e. lowering of heavy objects). The hydraulic oil enters the upper end of the hydraulic cylinder through the explosion-proof electromagnetic directional valve, and the return oil from the lower end of the hydraulic cylinder returns to the oil tank through the balance valve, hydraulic control one-way valve throttle valve, and explosion-proof electromagnetic directional valve. To ensure a smooth descent of heavy objects and safe and reliable braking a balance valve is installed on the return oil circuit to balance the circuit and maintain pressure, so that the descent speed does not change due to heavy objects. The throttle valve regulates the flow rate and the ascending and descending speed. To ensure safe and reliable braking and prevent accidents, a hydraulic control one-way valve, also known as a hydraulic lock, is added to ensure safe self-locking in the event of an accidental rupture of the hydraulic pipeline. An overload sound control alarm has been installed to distinguish between overload or equipment failure.Remember not to overload, overload is the root cause of many faults.An inverter can also generate high noise. When the power supply voltage is lower than % of the rated voltage, the short circuit ring of the iron core of the device breaks, the surface of the magnetic yoke and armature is skewed, dust or rust is poor, and the device will produce; Buzz&# quo; Noise.