GuangdongRail type cargo lifting platformThe quality directly determines the quality of the pipe fittings

Quarterly maintenance: Check the items checked each month　　?? The supervision unit shall effectively fulfill its safety responsibilities, and if any potential production safety accidents are found, it shall require the installation unit and the user unit to rectify within a specified period of time. If the installation unit and the user unit refuse to rectify, they shall promptly report to the construction unitGuangdongThe vibration frequency should be set to obtain large dynamic stress with low energy consumption, and the resonance frequency should be used to handle time dependent vibration. However, there may be one or more resonance peaks in large components and using resonance peaks with higher peaks and lower frequencies for aging can achieve optimal results. The resonance frequency needs to be determined by trial vibration, which slowly increases the speed of the excitation motor from , and determines the relationship curve between the amplitude of the workpiece and the motor speed to determine the resonance point of the workpiece. According to the scanning curve, a large acceleration was obtained at r/min, so r/min was determined as the aging frequency.Knowledge of pressure lifting platforms, boarding bridges, mobile elevators,GuangdongMovable scissor type lifting platform, and more is available in Jiuheng, Jinan. We sincerely welcome colleagues from all walks of life to visit and inspect the factory, cooperate and negotiate, and seek common development. The following maintenance and upkeep are required for the lifting cargo elevator: Maintenance and upkeep: Maintenance and upkeep should be carried out by the equipment operator or full-time personnel of the operating unit. The equipment maintenance and upkeep unit is responsible for supervising and reviewing the maintenance content. The main content of maintenance and upkeep is summarized as follows:; quot; Cross operation method; quot;: Clean, tighten, smooth, adjust, and prevent corrosion. Before and at the end of each shift, to minutes before and after each day, inspect all parts and components of the equipment to ensure they are normal. Apply oil smoothly according to rules, pay attention to the sound of mechanical operation, and do a good job in cleaning and handover to achieve the goal of clean appearance and normal operation of the equipment. Maintenance and handover records should be made in a fixed form and used for managementDiest, attention should be paid to maintenance to extend its lifespan. Below, Jinan Dasheng Hydraulic Machinery will introduce several maintenance and attention points for everyone: the brakes of each mechanism should be regularly inspected and adjusted for the clearance between the brake pads and wheels to ensure flexibility and reliability. On the friction surface, there should be no dirt present, and any dirt must be washed off with gasoline or thinner. Pay attention to checking each steel wire rope for broken wires and loose strands. If it exceeds the relevant regulations, it must be replaced immediately. Professional elevator manufacturers have a complete range of products, which are popular both domestically and internationally. Our equipment has a long service life! The industry leader in product wire products, welcome to inquireEvery customer pays attention to the price of elevators, so how does the manufacturer calculate the price of elevators? In general the manufacturer calculates the price of the elevator for customers based on the actual size, height, and carrying capacity of the on-site reserved opening provided by the customer Customers do not need to pay too much attention to the price difference between different elevator manufacturers when purchasing elevators, material brands, and production processes result in different prices for elevators Customers can consider the cost-effectiveness of elevators more when purchasing, with the principle of getting what they pay for. Safety hazard elimination plan for lifting cargo elevators: When there is a malfunction or abnormal situation in the lifting cargo elevator,GuangdongGuide rail platform lifting platform, it should be immediately stopped from use. After eliminating the malfunction and accident hazards, it can be put back into useThe reduction gearbox, gearbox, external meshing gear and other parts as well as the hydraulic oil, are all carried out according to the requirements in the table.

After cleaning, clean the filter and replace it with a new filter element before adding new oil. What adverse reactions may occur during the early use of hydraulic cargo elevators?Outdoor guide rail lifting platform, mainly used for high-altitude cargo transportation between floors. With a load capacity of - tons and an elevation of - meters, guide rail elevators, also known as hydraulic elevators, can be installed indoors and outdoors. They have a high lifting height and use side mounted oil cylinders, ensuring smooth operation, low noise, convenient maintenance, and long service life. In case of power failure, manual emergency descent can be used, which is safe, convenient, and practical. The pit depth is generally cm-cm. Professional elevator manufacturers have high pressure resistance, good waterproof performance, and fire and high temperature resistance, Strong overload capacity, corrosion resistance, radiation resistance, and can be used both internally and externally.Quarterly maintenance: Check the items checked each monthInterpretation and observation and can be customized according to the on-site environment. It is suitable for - story steel structures or concrete factories, and the brush pressure should be adjusted to ensure that its area is not less than %.Use a feeler gauge to check the wear condition of the worm gear of the worm gear reducer. Please refer to the instruction manual for specific requirements

The lifting stage can provide real-time information on the operation of the entire vehicle, avoiding relying solely on the experience of operators to coordinate with each other, and improving the reliability and safety of the system. The definition of safety zone is very important because the lifting stage has a large range of movements,GuangdongGuide rail type lifting platform, and it must be accurately calculated. The lifting stage has two structurally separate systems, the ground turntable and the high-altitude work bar. However, for various movements on the vehicle, it is also an interconnected system, which needs to consider the priority of operation, system redundancy, and safety assurance of actions.Price,Clean and inspect the crown wheel frame assembly, correct or replace with new partsEmergency stop: Press the emergency button switch to raise or lower the machine.Check all standard sections and diagonal support connection points. Check the fastening bolts of the gear rack and ensure that the motor cooling wing plate and organization are cleanGuangdong,Drop test to check if the braking interval of the safety governor meets the requirements of the rules. Equipment transfer maintenance: Check the coupling between the electric motor and the worm gear reducer, and dismantle the gearbox. Clean all components and seals, replace excessively worn and deformed parts and smooth oilAll connecting shafts must have split pins and be sufficient.Check the wear and clearance condition of the guide wheel of the cargo elevator