BayagunaLong shaft submerged slurry pumpVisual function of

　　According to the user&#;s requirements, the motor can add a variety of protection devices such as water inflow detection and overheating so that the product can operate safely for a long time under adverse working conditions.　　The two have certain commonalities. They are both submersible. As the name suggests, the pump is in an invasive state when running. The submersible slurry pump is a kind of submersible pump, but generally speaking, people often say that the submersible pump refers to the clean water pump, such as the submersible pump for domestic water and farmland irrigation and pumpingBayaguna,　　 before starting, check all circuits and switches to see if their wiring is correct and reliable then turn them over the ground for ~ minutes (the time should not be too long to avoid damaging parts or burning motor windings), and check whether the motor running direction is correct. If the above problems are not found, it can be started　　Strong strength and other advantages. It is widely used as a sealing device for various pumps. Place a water seal ring at the bottom of the packing box, and then place the filler.Uyo,BayagunaScrew deep well pump,　　The application of pumps involves all aspects of work and production, and some of the names are very similar, which makes it difficult to distinguish. Today,BayagunaSubmersible sewage pump, we will introduce the submersible pump and the submersible slurry pump. Is there any difference between the two　　 The standby submersible slurry pump shall roll the shaft / turn every week to make the bearing uniformly accept the static load and external oscillation. The building structure in the water pump room shall be reconstructed. Sound absorbing and isolating plates shall be installed around the wall and on the top of the machine room and fixed with light steel keel; The connecting holes between the machine room and other rooms are tightly blocked　　Second, the service life of the flow passage parts of the pump is relatively long, saving production costs.

　　The seal cannot bear the water pressure at this depth. Once the water leaks, the motor will not work normally, resulting in damage to the submersible slurry pump. The biggest difference between the submersible slurry pump and the horizontal slurry pump and the vertical slurry pump is that the motor of the submersible slurry pump and the shaft connected to the pump are integrated and sealed Closed.　　Correct the main shaft of the water pump and adjust the position of the water pump and the motor relatively.　　 If there is abnormal sound inside the slurry pump and there is no water, it is likely that the equipment may have air infiltrating into it when absorbing water, which will cause abnormal sound inside the pump, and then at the same time, the impeller is damaged or the impeller is damagedThe cheapest,　　The impeller of the submersible slurry pump may need to be disassembled for maintenance or repair during use. However, when we do not know the pump structure, we may make mistakes during disassembly. Let&#;s take a look at the correct disassembly of the impeller　　It will burn out. If there is a heating problem in use,BayagunaPipeline pump, you can refer to the following reasons.　　In the application of pumps, the first thing we think of is water. Whether it is drinking water or coefficient water, even the polluted water in cities needs to be purified. All these require its equipment to provide services for us. Without pumps, the equipment must be regularly maintained and overhauled to avoid blockage. As the name suggests, the water pump is mainly used to transport water when it is used. The effect of normal pumps is often better when it is used, but in fact, we use it at ordinary timesFair price,　　 Then reinstall the equipment on the engine and install the rubber hose.　　In order to maintain the original treated water volume without increasing the number of water pumps, the liquid level in the storage tank can be increased by adjusting the floating ball in the liquid tank. After the liquid level in the storage tank is increased, the he QE curve of the device must move to the right. At this time, the head at the intersection of the two curves becomes smaller and the flow remains　　 In addition, the noise method directly detects the noise of the equipment in the detection process, but this measurement will also be affected by the surrounding noise, so in fact,　　In the mud pump, the axial force is mainly composed of the pressure difference force of the liquid effect on the impeller and the gravity of the whole rolling part. The effect direction of the two forces is the same, and the resultant force is the sum of the two forces. If the submersible slurry pump is equipped with an auxiliary impeller, the liquid effect is on the auxiliary impeller　　It is also necessary to clean the ventilation duct to avoid blockage.　　This phenomenon shows that the failure of the pump is not only a material problem, but also reminds the pump designers and producers that in addition to good working conditions, the pump should also have good corrosion resistance, high reliability and long service life. The pump shall be designed in addition to the conventional design method of fluid mechanics