BitomThe elevator is goodHow to deal with various development difficulties

The use of the hydraulic lifting platform The user can choose the power mode and configuration according to his own scope of use: the power system includes: DC power supply, single-phase or three-phase power supply, and diesel engine.Anti-corrosion measures for the body of aerial work vehicles Pay attention to small scratches. The paint surface of aerial work vehicles is often corroded. In addition to common collisions, scratches small rocks on the driving tires, there may also be a peeling paint spot, they are easy to ignore. Therefore, check regularly, the engine compartment cover and its surroundings, and once found, go to a professional beauty shop for processing.Bitom,Seat belts Seat belts must be inspected once every six months, and they must be inspected or replaced by relevant units. It is strictly forbidden to use seat belts that have expired. When working in the following environments you should wear seat belts: In the scene where high-altitude operations are required, when entering the workplace , Workers must wear safety belts; when working at heights exceeding two meters, they must wear safety belts; in working environments where scaffolding is not used or there is no fence on the scaffolding, safety belts must be used when the working height exceeds meters; Safety belts must be used when working on the roof; on the top floor of a flat house, safety belts must be used when there is no protective fence within meters from the edge of the roof or the roof opening; the platform or workbench is in a suspended state; Safety belts must be used if there are openings on the ground near the roof or ladders; safety belts must be used when working at heights without safe fall prevention measures.The parts such as reduction box, gearbox, external gear and hydraulic oil are all in accordance with the requirements in the table.Tulln,Today, the editor will talk about a series of safety devices and their uses on the guide rail hydraulic lifting platform.It is strictly forbidden to switch the electric control switch with wet hands. Many people tend to ignore this detail. Although the safety voltage of the hydraulic lifting platform is below V, if you touch the power supply with your hands, it may cause lifting failure in light cases, or electric shock accidents in severe cases.Brake operators of various mechanisms on the equipment should regularly check and adjust the gap between the brake shoe and the brake wheel to ensure flexibility and reliability. Long-term promotion of freight elevator factory, old brand, price advantage, quality guaranteed!

Outriggers: mechanical outriggers, hydraulic outriggers, ordinary hand-operated outriggers, pull-out outriggers.Things to keep in mind when working at heights When working at a height exceeding . meters, you must use safety nets or safety belts.Secondly there must be no dirt on the friction surface. If there is dirt, it needs to be washed off with gasoline or thinner; the gear box, external gear and other parts of the equipment and the hydraulic oil must be in accordance with the requirements in the table; Correctly maintain the hydraulic guide rail lift. Regularly check whether the wire ropes in each part are broken or loose. If this phenomenon is found, replace them in time. If there is any looseness, it should be tightened in time. The connecting bolts of the equipment should be checked for tightness when the body is under pressure. All connecting shafts should be equipped with cotter pins; check whether each mechanism is operating normally, whether there is noise or failure , to eliminate all faults in a timely manner; when installing, dismantling and adjusting the slewing mechanism of the equipment,BitomFixed lifting cargo elevator, it is necessary to pay attention to the parallelism between the reducer and the center line of the gear, and the appropriate meshing gap; conduct a comprehensive inspection of the equipment regularly, whether the wires and cables are If there is damage, whether the motor is overheated, replace it in time and continue to run after troubleshooting; ensure that the bearings of the motor, distribution box and brushes must be kept clean, and the travel switch points of each safety device must be safe and reliable.Analysis project,Hydraulic system: mainly oil cylinders, high-strength chrome-plated rods, Japanese NOK seals self-made external integrated pump stations, oil pipelines, gear pumps, solenoid valves, etc. The Japanese NOK seal used in the oil cylinder has good wear resistance, which ensures that the oil cylinder series will not leak oil for a long time. The gear pump pumps the oil in the oil tank into the oil circuit and enters the oil cylinder, thereby driving the top of the rod and raising the equipment; The valve is used to adjust the oil output, the ascending and descending speed, and contains an emergency descending device to ensure that the guide rail hydraulic lifting platform can descend safely in case of an emergency.Check the front page of the oil pipe to check whether the skin of the oil pipe of the hydraulic lifting platform is damaged or cracked, and if so, replace it immediately; secondly check whether there is any sign of looseness at the connection between the oil pipe and the oil pipe, and if so, tighten it immediately to avoid lifting on the hydraulic lifting platform There is an oil spill in the process, which leads to accidents; what items need to be checked before using the hydraulic lifting platform? Cut off the power first to avoid tragedies such as electric leakage and electric shock)The parts such as reduction box, gearbox, external gear and hydraulic oil are all in accordance with the requirements in the table.

In the construction elevator, the switch box also has leakage protection equipment. Its wires and cables are well insulated, without leakage, and the metal threaded is not rusted, and its damage is close to zero. His steel wire rope should comply with the corresponding configuration requirements, and there is no problem of broken strands and diameter reduction. Of course, the number of broken wires should not exceed the corresponding standard. His pulley movement is very flexible.supply,BitomTen ton lifting cargo elevator,What is the new price of a fixed lift? Professionally improve the quality assurance of the freight elevator factory. The preferential activities are in progress, and new and old customers are welcome to come to consult.Fixed boarding bridge: The fixed boarding bridge is a special auxiliary equipment to realize the fast loading and unloading of goods. Its height adjustment function uses a bridge between the truck and the cargo platform of the warehouse, Only one person is required to operate, and the rapid loading and unloading of goods can be realized. It enables enterprises to reduce a lot of labor, adjust the PCS system ring to align the side hole with the dust-proof hole, and tighten the inner hexagon. After that, remove the motor shaft key.Bitom,The hydraulic lifting platform can be divided into: four-wheel mobile type,BitomTwo ton lifting cargo elevator, two-wheel traction type, car modified type, car type, auxiliary self-propelled type, and the lifting height ranges from a meter to s meter.Regular maintenance Regularly check whether the circuit system of the hydraulic lifting platform is loose, and check whether the wires and cables are aging and damaged, which may cause leakage of the line. If there is, it should be repaired in time to avoid electric shock.What types of lifts are there? There are many types of this equipment, for example, it can be divided into fixed lifting devices and vehicle-mounted lifting devices according to the form of movement. The so-called fixed lifting means that it is generally installed in one place and fixed, and then the lifting operation can be carried out. This type of lifting equipment is generally used more on the assembly line. Some large-scale production lines need to move the material when loading materials. Lifting to a certain position, and then putting it into the production line for production, a special lifting device is required to be fixed at a certain position of the production line.