KohutepecIrrigation deep well pumpHow to distinguish the rotation direction

　　It is not correct that it has no effect on us.　　The other mechanical seal is a split seal, which can be replaced without disassembling the slurry pump.Kohutepec,　　 Easy installation and maintenance. Small submersible sewage pumps can be installed freely. Large submersible sewage pumps are generally equipped with automatic coupling devices for automatic installation, it can drive the impeller to rotate so as to drive it to flow.San-Antonio-de-los-Banos,　　The structure of the submersible slurry pump will be more intuitive. First, the equipment will use centrifugal force to drive the liquid from the impeller to the outer edge and obtain energy, and then leave the edge of the impeller at a higher speed　　If the oil seal ring of the shaft is seriously worn replace it with a new one.　　In order to make the equipment perform better when it is used, but this also needs to be based on its working principle. It can not be adapted at will when it is optimized.

　　What stands out is the sealing of the container. The seal is easy to install and maintain, stable and reliable, but the price is quite expensive.　　 Pipeline single-stage single suction chemical pump. Pipeline pump used for transporting chemical corrosive liquid in textile, pharmaceutical, health, food, chemical, petroleum, oil refining and other industries, with the service temperature not higher than ° C. It is an ideal product to replace the traditional chemical pump.　　 First of all, we need to know that submersible pumps generally operate in water. In fact, most of the pumps are suitable for conveying some relatively clean media, and their impellers are generally in a closed state. However,　　 The fan speed of the water pump is too low, and the air pressure and air volume are relatively small,KohutepecWater well pipeline pump, so the heat cannot be dissipated.　　 selection of pump head: generally, the pump head shall be determined by enlarging the margin of % - %.　　Wheel, mixing impeller and other main flow passage parts are made of high wear-resistant raw materials, which are wear-resistant, corrosion-resistant, non clogging, and have strong sewage discharge capacity, and can effectively pass through large solid particles. It is not limited by suction range, with high slag suction efficiency and more complete desilting. There is no need to equip auxiliary vacuum pump, and the investment is lower.

　　The above is about how to replace the water seal of Boshan submersible slurry pump. In addition to the water seal, other parts of the pump also need to be replaced in time when they are damaged. Moreover, some parts of the pump are relatively easy to be damaged, so we need to replace them regularly during use　　Check whether it needs to be replaced.Price,　　 A vent pipe is installed at the bottom of the pump, so that when the pump is buried underground water will be injected into the bottom of the slurry pump through the vent pipe, so that a sand water mixture will be formed at the bottom of the slurry pump, so that the slurry pump can be started normally. The advantage of this approach is that even if　　The treatment methods are as follows: Check the power supply voltage: if the voltage changes greatly, it is caused by unstable voltage,KohutepecPipeline pump, and the use should be stopped immediately to prevent more serious consequences. Or install corresponding heat dissipation protection measures to protect the motor.　　 The pump body (can not) bear the pressure from the outlet pipeline system. The standby pump in the warehouse should rotate (/ times a week to make the shaft bear the load and external vibration evenly. The belt CR drive is that the motor is on the (right) side of the pump from the inlet of the pump.Kohutepec,　　The above is about how to replace the water seal of Boshan submersible slurry pump. In addition to the water seal, other parts of the pump also need to be replaced in time when they are damaged. Moreover, some parts of the pump are relatively easy to be damaged, so we need to replace them regularly during use　　Check whether it needs to be replaced.　　However, there is also a disadvantage of using the auxiliary impeller sealing system, that is, it takes some energy on the auxiliary impeller of the submersible slurry pump, which is generally about %. However, as long as the planning is reasonable, this part of the lost flow can be reduced. The slurry pump is mainly applicable to electric power, etc. and handle it at any time.