ComlowLarge hydraulic lifting platformStop falling and rebound

Ensure that there is a suitable power supply at the installation site, and separate maintenance of the distribution box is required. The distribution box should have a leakage switch, and the hydraulic cargo elevator construction site should be equipped with a fire extinguisher to prevent welding operations from causing fires. When selecting a leakage switch, it will not cause lifting. At this point, you only need to add enough hydraulic oil to run.Comlow,Usage and instructions for steel wire ropes in elevators: The steel wire ropes of the steel wire ropes require very high strength, usually made of high-quality carbon steel with a carbon content of .% -.%. They are widely used as transmission components in elevators. Due to its large load-bearing capacity, light weight,ComlowHydraulic lifting platform truck, smooth operation, no noise, suitable for high-speed transmission, high strength, strong overload capacity, and reliable operation, it has become a commonly used rope for hydraulic elevators.Protective device: In case of power or oil circuit failure, there should be a safety rope to prevent the workbench from falling out of control. (Allow controlled descent)Vasilevo,Each brush should be kept clean on its surface, and the brush pressure should be adjusted to ensure that its area is not less than %.The hydraulic lifting platform often checks the connection status of each part, and if there is any looseness, it should be tightened. The connection bolts of the machine body should be checked for tightness when the elevator body is under pressure (the compression condition can be formed by rotating the arm). All connecting shafts need to have split pins and need to be fully opened.To consider its capacity, generally mobile equipment takes - times the high flow rate of pump Z, and fixed equipment takes - times.

There is a phenomenon of self stopping when running up and down. Due to poor contact of the safety protection switch, it is easy for hydraulic cargo elevator manufacturers to cause this problem.Generally speaking, for situations with large lifting loads and small lifting heights, a lifting mechanism should be selected. For situations with small loads but large lifting heights,Comlow20 meter hydraulic lift, a lifting mechanism should be selected. According to the initial structure of the jacking, in order to meet the stability requirements, the size and lifting type of the oil cylinder are increased, and in order to achieve the same effective area as the jacking force, the oil cylinder is added. If the latter is larger, a lifting mechanism should be selected.Therefore,ComlowHydraulic lifting platform, the wholesale manufacturers of hydraulic elevators remind that there are three main ways to adjust the speed control circuit: throttling speed control circuit: quantitative pump oil supply, using flow valves to adjust the flow in and out of the actuator to achieve speed control; In the volume throttling speed control circuit the oil is supplied by the pressure limiting variable pump, and the flow rate into the actuator is adjusted by the flow valve to adapt the flow rate of the variable pump to the regulated flow rate of the speed control valve.investment,Lines of various safety equipmentRemove the hydraulic oil tank filler cap, inspection hole, hydraulic oil pipe and other parts to avoid dust when removing the system oil pipe. Clean the disassembled parts before opening them. When disassembling the hydraulic oil tank filler cap, first remove the soil around the tank cap, loosen the tank cap, and remove any remaining debris from the joint (do not rinse with water to prevent water from seeping into the tank). After confirming cleaning, open the tank cap.Reason: Manual pump and gear pump have severe oil leakage. Cleaning method: Replace the oil pump sealing ring to clean it. Reason: Gear pump is damaged, and the contact crater should be polished in a timely manner.For more please check,Regularly inspect the hydraulic lifting equipment of the upper and lower materials to ensure the safety of the rail type elevator and the safety of the material supply to the rail type lifting platform.It is not allowed to throw tools and materials up and down and ropes should be used to tie or hang them to avoid injuring workers or scaffolding below.An inverter can also generate high noise. When the power supply voltage is lower than % of the rated voltage, the short circuit ring of the iron core of the device breaks, the surface of the magnetic yoke and armature is skewed, dust or rust is poor, and the device will produce; Buzz&# quo; Noise.Comlow,The electromagnetic coil of the electromagnetic directional valve is not firmly fixed, and frequent separation and suction can also produce high noise.Stable and widely applicable cargo lifting equipment is mainly used for transporting goods between height differences in production lines; Material online and offline; Adjust the height of the workpiece during assembly; High altitude feeder feeding; Lifting of components during assembly of large equipment; Large machine material and cutting; The warehouse loading and unloading site is equipped with forklift and other transportation vehicles for rapid loading and unloading of goods.The lifting platform is placed on a horizontal support surface, and the concentrated load of MAX load capacity is placed at any position mm away from the periphery of the workbench. After lifting times, each load-bearing component must not have deformation or cracks.