YagodinaHow much is the I-beam of 14 per meterCommodity market has a greater impact

C-section steel has uniform zinc layer, strong adhesion, no zinc scar, no zinc leakage and high dimensional accuracy. All surfaces are wrapped by zinc layer, and the zinc content on the surface is usually -g /? It has long service life, corrosion resistance and durability. It is a kind of stronger protection.→ under the same section load,The pipeline shall be positioned according to the drawing design, and the pipeline support shall be prefabricated according to the site conditions. Hang the wire from the th floor down and fix the support.I-beamAmbilobe,Plan option : Martensitic chromium alloy pipe,After determining the reasonable pickling agent and polishing solution, it is very easy to carry out hot galvanizing for relevant alloy pipes. Use 'phosphating treatment' to degrease the pipes of electrolytic machine equipment, put them into the aqueous solution with zinc salt after pickling and passivation, connect the negative level of electrolytic machine equipment, put them into the cold-rolled steel plate in the direction corresponding to the pipes, and connect the switching power supply, If the current flows from the positive stage to the negative stage, a layer of zinc is deposited in the pipe.I-beam is a kind of economical section steel with better section mechanical properties. Its characteristics are as follows:

Plan scheme : high carbon steel with carbon content exceeding .% and alloy pipe with chromium content not less than %The production of plastic impregnated welded steel wire mesh is to immerse the formed welded steel wire mesh into a stone groove filled with PVC powder. The dry forming process is complex and the cost is much higher than that of spray welded mesh. Due to different application ranges and different uses,YagodinaHow much is I-beam per meter, the choice is expensive or cheap, which needs to be determined according to its actual use.Alloy pipe is a very important way and type of seamless steel pipe. Its use is relatively common. It is widely used in various engineering projects, house construction and building decoration. Its fracture will always be found in the production, manufacturing and key marketing of alloy pipe,Yagodina35CrMo thick wall alloy pipe, That is, many stages of production and processing are not done well. Another is that the seasoning is not enough and the proportion of chemical molecules is wrong. There are all reasons.wholesaler,The utility model has the advantages that the axial force of the roll is small, the axial movement is small, the working inclined plane is not required, the pass occupies a small length of the roll body, and more passes can be matched under the condition of a certain length of the roll body.Plan option : Martensitic chromium alloy pipe,I-beam is widely used in buildings or other metal structures.

Alloy pipe is a spiral seam seamless steel pipe, which is made of hot-rolled strip steel coil, often processed by warm extrusion and welded by automatic double wire double side arc welding process. The alloy pipe sends the hot-rolled strip steel to the welded pipe unit and the hot-rolled strip steel is extruded through multiple passes. The hot-rolled strip steel is rolled slowly to produce annular pipe material with open mouth gap. Adjust the reduction amount of the extrusion roll to control the welding gap at ~ mm and make both sides of the weld flush.Welcome calls ,When it is used for ground heating and hot spring transportation, it can meet the requirements of refrigeration and achieve the practical effect of less damage. It is applicable to water conservancy engineering, mining and other industries to meet the provisions of cold, cold and corrosion prevention. In addition, the chemical raw material transmission pipeline has a wide indoor space.Oxygen blowing welded pipe: it is used as steel blowing pipe. Generally, small-diameter welded steel pipe is used. There are eight standards from / inch to inch. Made of , , , or q-q steel strip. In order to prevent corrosion, some are aluminized.Stages needing attention in the production and manufacture of alloy tubesYagodina, physical and chemical properties, in addition to the reasonable selection of materials and forming process, heat treatment process is often necessary. In addition, the mechanical, physical and chemical properties of aluminum, copper, magnesium, titanium and their alloys can be changed by heat treatment to obtain different service properties.The crack mainly occurs at -mm from the edge of the alloy pipe. The shape is several parallel vertical cracks of different sizes. The regularity is that the thicker the specification and model of the alloy pipe is The wider the width, the more serious the disadvantages.The flange of H-beam is of equal thickness including rolling section and combined section composed of three plates welded. All I-beams are rolled sections. Due to poor production technology, the inner edge of the flange has a slope of : The rolling of H-beam is different from that of ordinary I-beam. Only one set of horizontal rolls is used. Because its flange is wide and has no inclination (or the inclination is very small), a group of vertical rolls must be added for rolling at the same time. Therefore, its rolling process and equipment are more complex than ordinary rolling mills. The maximum height of rolled H-section steel that can be produced in China is mm, which exceeds the welded composite section.