AkureriSewage pump divingAccurately grasp the basic connotation of opening up

　　 In addition,AkureriHH slurry pump, the use of ° and S-shaped bends should be reduced as much as possible during the installation and design of pipelines.　　After meters, the sealing of the equipment can not bear the water pressure at this depth.Akureri　　The actual operating flow is too large, resulting in the following results: when the flow increases, the shaft power of the pump increases, while the efficiency of the motor remains unchanged, so the power of the input motor must increase. Excessive power makes the motor in an overloaded operation state, which may cause heating or even burn out the motor　　Avoid airborne sound transmission; Ensure the airtightness of machine room doors and windows. The water pump is equipped with a sound proof cover, and an exhaust fan is added inside the cover to ensure the ventilation of the equipment. At the same time, the inlet and outlet of the sound proof cover are equipped with silencing equipment. A vibration isolation platform is installed at the bottom of the water pump for foundation vibration reduction to isolate the vibration generated during the operation of the water pumpDenov,　　The above introduction is about the cause ysis of the overload of the slurry pump. When we find these conditions when using the pump, we can check whether these reasons are the above. This is also a reminder that we need to maintain the pump during normal use. latent　　Submersible slurry pump is a kind of pump that can adapt to various working conditions and can treat various sewage from environmental protection industry. Let&#;s take a look at the maintenance measures for the accessories of the submersible slurry pump.　　There will be no insufficient liquid supply or other problems.

　　If the oil seal ring of the shaft is seriously worn replace it with a new one.　　If it can be started and operated with lubricating water, self-lubricating bearings can be used at the support, or other types of bearings (such as polymer bearings) can be used according to the design or contract requirements.　　Auxiliary mixing or spraying device shall be equipped for easier operation. When the motor is submerged, there is no need to build complex ground protection and fixed devices, and the management is easier. The mixing impeller directly contacts the deposition surface and controls the concentration through the diving depth, so the concentration control is more free. Equipment directly submergedpacking,AkureriCorrosive pipeline pump,　　 If the pump is equipped with a vacuum gauge or pressure gauge, close the cock connected with the submersible slurry pump before starting the motor, open it after the speed is normal, and then gradually open the outlet sluice valve. If the flow is too large, if the flow is too small, the correct application is very important. Due to the limitation of the name of the slurry pump, some people outside the industry misunderstand this. In fact the impurity pump, dredging pump, desilting pump, etc. are all in the application scope of the slurry pump　　The above four methods can be used to detect whether the submersible slurry pump has cavitation, because if the equipment is in use, it will have a great impact on the operating efficiency. Even if the cavitation time is long, it will also have a certain impact on other parts of the equipment. Sometimes submersible slurry pump

　　Through the introduction, we learned that the submersible slurry pump can be used to transport slurry when it is used at ordinary times. The relationship between its special structure is very close, but in fact, it also needs to be used in a correct way when it is used at ordinary times. Only in this way canScheme customization,　　Basically, the reasons for the motor heating of the submersible slurry pump are the above items. If the motor heating occurs, it must be noted that if the fault is caused by electricity, people who do not know electricity should not repair it by themselves, so as to avoid people　　Domestic stainless steel pipeline pump products have greatly improved their technical level through introduction, absorption, renovation, digestion and innovation. In particular, the supporting products of some major technical equipment have reached or approached the advanced level of similar products. With the continuous expansion of the market, stainless steel pipeline pump　　The other mechanical seal is a split seal, which can be replaced without disassembling the slurry pump.Akureri,　　 confirm whether the pressure capacity of the pipeline meets the requirements, and conduct hydrostatic test if necessary.　　Although the shaft seal occupies a small position in the pump, the normal operation of the pump is closely related to the shaft seal.　　So it is called: submersible slurry pump.