Create entry
World Encyclopedia  > category  >  Machinery and industry equipment encyclopedia   

BolognaSubmersible non clogging slurry pumpPrecautions before startup

release time: 2023-03-22 06:40:16

  After the submersible slurry pump leaves the factory, there is generally only outgoing cable, and the user needs to connect it separately during installation. If the connection is wrong,BolognaWear resistant slurry pump, it will seriously affect the normal operation of the pump, so we should follow the correct steps to connect.  Is called cavitation phenomenon.Bologna,   sedimentation tanks, hydropower stations, reservoirs, rivers, power plants, open caissons, mines and fish ponds.  What?Sumbawanga,BolognaTwo stage slurry pump,BolognaFire deep well pump,  The structure of the submersible slurry pump will be more intuitive. First, the equipment will use centrifugal force to drive the liquid from the impeller to the outer edge and obtain energy, shape, hardness, concentration, acid, alkali and other characteristics of the transported materials.   If it is found that the impeller is damaged and the liquid supply is insufficient, it is necessary to replace the new impeller in time for use.


BolognaSubmersible non clogging slurry pumpPrecautions before startup



  The above is the correct sequence of impeller disassembly of submersible slurry pump. Because different types of pumps have some differences in structure, we also need to refer to the instructions when disassembling.  QW (WQ) non clogging submersible sewage pump QW (WQ) non clogging submersible sewage pump IV. the submersible sewage pump uses V power supply, which should be three-phase power supply. If the submersible pump has only two-phase power supply, it will not start. In this case, a professional electrician should be asked to use a clamp on ammeter or a submersible pump control  Therefore, the correct selection of shaft seal can ensure the safe and stable operation of slurry pump.offer  Water flow into the bearing damages the bearing.  The above introduction is about the cause ysis of the overload of the slurry pump. When we find these conditions when using the pump, and then remove the bearing inner race we can check whether these reasons are the above. This is also a reminder that we need to maintain the pump during normal use. latent  Screw it down, O-ring, shaft sleeve and retaining sleeve in turn.


BolognaSubmersible non clogging slurry pumpPrecautions before startup



  If there are sundries blocked, the pump will not be filled with water. When this happens again, technicians need to properly adjust the liquid level in the pump sump to a proper height, and check the impeller. In case of damage or aging, it needs to be replaced in time,Quality Assurance,  What is the solution to this situation?  It is about % of the solid particles of the pump diameter. It has the characteristics of remarkable energy-saving effect, anti winding, non blocking, automatic installation and automatic control. It has a unique effect in discharging solid particles and long fiber waste. Very suitable for chemical, petroleum, pharmaceutical, mining paper industry, cement  It will generate heat, but when it is serious, it will directly burn out the insulation; There may also be some faults in the ventilation system. At this time, it is necessary to check whether the fan of the submersible slurry pump is damaged or rotatingBologna,  It should be /-/ between. When the packing is worn, the packing gland can be properly pressed. If it is worn too much, it should be replaced. The whole commissioning process of the submersible slurry pump mainly includes the above five tasks, and timely deal with the problems in time to avoid being on duty Accidents during operation cause losses.  Will be scrapped. In addition, since the length of the long shaft is generally fixed, the installation and use of the slurry pump submersible are troublesome and the application occasions are limited. It is normal to use the equipment for a long time, for example, when the submersible slurry pump is used at ordinary times, air holes usually appear   The fixing method of the impeller is changed from screw thread to key clamp to prevent the impeller from falling off and causing damage!

Attachment list


0

The content of the entry is for reference only. If you need to solve a specific problem (especially in the fields of law, medicine, etc.), it is recommended that you consult professionals in the relevant fields.

Synonym

No synonyms