HainingWhere is 40CrMo seamless pipeHow is the production status

C-section steel has uniform zinc layer, smooth surface, strong adhesion, no zinc scar, no zinc leakage and high dimensional accuracy. All surfaces are wrapped by zinc layer, and the zinc content on the surface is usually -g /? It has long service life, mining and other industries to meet the provisions of cold it can meet the requirements of refrigeration and achieve the practical effect of less damage. It is applicable to water conservancy engineering, cold and corrosion prevention. In addition, the chemical raw material transmission pipeline has a wide indoor space.Haining,How are seamless tubes made?Aiming at the connective tissue and texture produced in stainless steel plate Position and other crystal defects are generally removed by heat treatment processes such as quenching or quenching. The effect of quenching is to optimize the crystal eliminate structural defects, reduce strength, improve plastic deformation, and also conducive to cold drawing. In the production and manufacture of cold drawn alloy pipe, the formulation of appropriate annealing process is a necessary condition to ensure that the alloy pipe mechanism meets the standard and the commodity does not crack. If the manufacturer in order to better one sidedness, reduce the product cost and reduce the quenching process, it will eventually lead to bad harm to the product quality.Olsztyn,When selecting I-beam in structural design, reasonable I-beam shall be selected according to its mechanical properties,Haining25 welded pipe is more than one meter, chemical properties, weldability and structural size.Plan scheme : high carbon steel with carbon content exceeding .% and alloy pipe with chromium content not less than %Aiming at the connective tissue and texture produced in stainless steel plate Position and other crystal defects are generally removed by heat treatment processes such as quenching or quenching. The effect of quenching is to optimize the crystal,HainingHow much is welded pipe 219, eliminate structural defects, reduce strength,HainingHow much is 32 galvanized pipe, improve plastic deformation, and also conducive to cold drawing. In the production and manufacture of cold drawn alloy pipe quenching machinery and equipment cannot be lacked. Therefore, the formulation of appropriate annealing process is a necessary condition to ensure that the alloy pipe mechanism meets the standard and the commodity does not crack. If the manufacturer in order to better one sidedness, reduce the product cost and reduce the quenching process, it will eventually lead to bad harm to the product quality.

I-beam has wide flange, thin web, many specifications and flexible use. It can save metal by % ~ % when used in various truss structures. Because the inner and outer sides of the flange are parallel and the edge end is at right angles, it is easy to assemble and combine into various components, which can save about % of the welding and riveting workload, greatly accelerate the construction speed of the project and shorten the construction period. Carbon: the higher the carbon content, but the worse its plasticity and toughnessUnder the action of thermal stress, because the initial temperature of the surface layer is lower than that of the heart and the shrinkage is greater than that of the heart, the heart is pulled. At the end of cooling, because the final cooling volume shrinkage of the heart cannot be carried out freely, the surface layer is compressed and the heart is pulled. That is, under the action of thermal stress, material composition and heat treatment process. The faster the cooling rate, the higher the carbon content and alloy composition, the greater the uneven plastic deformation caused by thermal stress during cooling, due to the change of microstructure during heat treatment, i.e. the transformation from austenite to martensite, the increase of specific volume will be accompanied by the expansion of workpiece volume, and each part of workpiece will undergo phase transformation successively, resulting in inconsistent volume growth and structural stress. The final result of the change of tissue stress is the tensile stress on the surface and the compressive stress in the center, which is just opposite to the thermal stress. The microstructure stress is related to the cooling rate, shape and chemical composition of the workpiece in the martensitic transformation zone.packing,Difference and application description between H-beam and I-beamAfter determining the reasonable pickling agent and polishing solution, it is very easy to carry out hot galvanizing for relevant alloy pipes. Use 'phosphating treatment' to degrease the pipes of electrolytic machine equipment, put them into the aqueous solution with zinc salt after pickling and passivation, connect the negative level of electrolytic machine equipment, put them into the cold-rolled steel plate in the direction corresponding to the pipes, and connect the switching power supply, If the current flows from the positive stage to the negative stage, a layer of zinc is deposited in the pipe.C-section steel has uniform zinc layer, smooth surface, strong adhesion, no zinc scar, no zinc leakage and high dimensional accuracy. All surfaces are wrapped by zinc layer, and the zinc content on the surface is usually -g /? It has long service life, corrosion resistance and durability. It is a kind of stronger protection.

Xhy- series high hardness alloy I-beam; Undertake drawings and process wear-resistant pipes（ Φ ≥mm）； Undertake the processing and production of vulnerable parts of cement machinery; Welding technology consultation and service; The wear-resistant layer of alloy wear-resistant plate of high chromium heap welding flux cored wire series is mainly high chromium, as well as manganese, molybdenum, niobium, francium and other components. The alloy carbide formed has strong stability at high temperature.Installation works, The small length of repair welding is mm; The raw material shall not exceed mm after grinding by welding edge.Galvanized pipe is actually galvanized pipe. This is mainly because it increases the corrosion resistance of the steel pipe, so it is evenly coated with a layer of zinc. It can prevent the erosion of other chemicals such as and steam, and protect the steel strip. It is non-destructive and effectively prolongs its service life. Generally, the steel strip purchased is rolled into a large number by the galvanized pipe manufacturer, so pay attention to it during storage. Cold extrusion. This kind of processing method is more purposeful. Before the preparation of steel processing and extrusion molding when the extrusion molding is used for mm diameter pipe fittings, the investment of machinery and equipment is less, so the raw material consumption is also very small, and the technology is relatively perfect. Once the tube size is increased the cold extrusion method must have large cargo capacity and high-power machinery and equipment. Therefore, the automatic control system will be upgraded.Haining,Introduction to product knowledge of alloy pipe:I-beam is an economic section high-efficiency profile with more optimized section area distribution and more reasonable strength weight ratio. It is named because its section is the same as the English letter 'H'.Patented manufacturing process of I-beam: I-beam has become a new industrial standard for wear-resistant materials