Hard50 galvanized square pipe priceLarge factory quality

The welding process of square tube is analyzed. The square tube is produced and processed at room temperature with strip steel as raw material. Square pipe can be divided into straight seam welded pipe, square pipe and spiral welded pipe. Due to the different uses of welded pipes, the standards of welded pipes are summarized in turn: galvanized qb square pipe for low-pressure fluid transportation, and the standard number is gbt-. Representative materials: QA, qbqb, etc. It is mainly used for conveying water, gas, air, oil and heating hot water or steam, and its purpose is limited to general low pressure fluid.Square tubes are classified by forming: forged steel; Cast steel; Hot rolled steel; Cold drawn steel.Wewak,There are many ways of ignition, such as arc, electric spark, flame, strong current, high-temperature furnace, electron beam, laser, high-temperature radiation, microwave, chemical furnace, etc.High quality steel (P & le; .%, S & le; .%)Square tube production most square tube processing is square tube pressure processing resulting in plastic deformation of the processed steel (billet, ingot, etc.). According to the square tube processing temperature, the square tube can be divided into cold processing and hot processing. The main processing of square tube includes: rolling: the gap (various shapes) between the square tube metal blank and the rotating roll , because of the compression of the roll, the material section is reduced and the length is increased. This is a common production method for producing square tubes. It is mainly used to produce square tube profiles plates and tubes. It is divided into cold rolling and hot rolling.

The square tube for fluid transportation (gbt-) is a general square tube for transporting water, oil, gas and other fluids.High productivity of square tube: the efficiency of cold production of mechanical parts is very high, especially for parts with large batch. Cold production can be several times, several times or even hundreds of times higher than cutting. For example, the use of cold pin for automobile is twice higher than that of cutting. At present, cold pin automata is used to improve productivity. The productivity of table cooling automata is equivalent to that of ordinary lathes or shaft self-propelled machines.When storing QB square pipe, we need to select a suitable place. We need to think about many external factors, such as the corrosivity of steel pipe etc. Therefore, the place must be clean, dry and ventilated, where harmful gases appear, QB square pipe can not appear,HardWhere does galvanized square tube sell, weeds and other sundries should be removed in time, and the outer surface of steel should be kept clean. If there are acid, alkali, salt, etc. in the warehouse, so try to cut it and don't let it. In addition, if we can think about those higher metal products, we can put them into the warehouse for very good retention. According to geographical conditions, there is a sealed warehouse, but the ventilation setting is excellent. The difference between QB square tube and seamless steel tube QB square tube is a kind of high-precision steel tube material after cold drawing or hot rolling treatment. QB square tube is mainly used to produce products of pneumatic or hydraulic components, which can be seamless pipe or welded pipe, because there is no oxide layer on the inner and outer walls of QB square tube, no deformation under high pressure, high precision, high finish, cold bending, flaring and flattening without cracks. The chemical composition of QB square tube includes carbon silicon Si, manganese Mn, sulfur s, phosphorus P and chromium CR.packing,If the re inspection results are unqualified (including the items whose preliminary inspection results are unqualified and re inspection is not allowed) the supplier can submit them for acceptance one by one; Or re conduct heat treatment (the number of RE heat treatment shall not exceed times), and propose acceptance with a new batch.Put the pig iron for steelmaking into the steelmaking furnace according to the specified process to obtain steel. The products of steel include ingots, continuous casting billets and various steel castings made of straight square tubes. Generally speaking, steel refers to the steel rolled into various square tubes. Square tube steel belongs to ferrous metal, but steel is not completely equal to ferrous metal.Square pipe for diamond core drilling (gb-) is a square pipe for drill pipe, core rod and casing for diamond core drilling.

Strength refers to the performance of metal materials under static load (excessive plastic deformation or fracture). Since the action modes of load include tension, compression, bending and shear, the strength is also divided into tensile strength, compressive strength flexural strength and shear strength. There is often a certain between various strengths. Generally, tensile strength is used as the basic strength indicator. Appropriate sites and warehouses shall be selected. The sites or warehouses for storing steel pipes shall be in clean and unobstructed places, away from factories and mines that produce harmful gas or dust. Weeds and sundries shall be removed on the site to keep the steel pipe clean; In the warehouse, it is not allowed to stack with acid, alkali, salt, cement and other materials that are corrosive to the steel pipe. Different types of steel pipes shall be stacked separately to prevent confusion and corrosion; Large section steel, rail, steel plate, large-diameter steel pipe, forging, etc. can be stacked in the open air; Small and medium-sized section steel, wire rod, medium diameter steel pipe, but they must be covered and padded; Some small steel pipes, steel sheets, steel strips, silicon steel sheets or thin-walled steel pipes, all kinds of cold-rolled and cold drawn steel pipes and high and corrosive metal products can be stored in the warehouse; The warehouse shall be selected according to geographical conditions, and generally adopts ordinary closed warehouse, that is, the warehouse with roof, enclosure, tight doors and windows and ventilation devices; The warehouse is required to pay attention to ventilation in sunny days, close and damp proof in rainy days, and often maintain a suitable storage environment. The principle of reasonable stacking and first in first stacking is to stack according to varieties and specifications under the condition of stable stacking and ensuring safety. Materials of different varieties shall be stacked separately to prevent confusion and mutual corrosion; It is forbidden to store articles that have corrosive effect on steel pipes near the stacking position; The bottom of the stack shall be padded high,Hard2-inch galvanized square pipe, so as to facilitate the implementation of the principle of first in, first out; The section steel stacked in the open air must be provided with wooden mats or strip stones. The stacking surface is slightly inclined to facilitate drainage. Pay attention to the straightness of the material placement to prevent bending and deformation; The stacking height shall not exceed m for manual operation m for mechanical operation, and m for stacking width; A fixed channel shall be reserved between stacks, generally .m,HardWhat kind of galvanized pipe is 32, and the access channel is generally ~ om depending on the size of materials and transportation machinery; The bottom of the stack shall be padded up. If the warehouse is cement floor, it can be padded up by .M; If it is muddy ground, it must be padded . ~ .m high. If it is an open site, the cement ground shall be padded with O & middot; ～O· m, . ~ . m higher than the sand and mud surface, the angle steel and channel steel shall be stacked in the open air, i.e. the mouth shall face down, and the I-beam shall be placed vertically. The i-groove surface of the steel pipe shall not face up to avoid ponding and rust. The packaging and protective layer of the protective materials shall be coated with agent or other plating and packaging before leaving the factory, which is an important measure to prevent material corrosion. Attention shall be paid to protection during transportation, loading and unloading and shall not be damaged, the warehouse shall be kept clean and the maintenance of materials shall be strengthened. Before warehousing, materials shall be prevented from being drenched or mixed with impurities. Materials that have been drenched or contaminated shall be wiped according to their properties, such as steel wire brush for high hardness and cloth, cotton and other materials for low hardness; The materials shall be regularly after warehousing. If there is corrosion, the corrosion layer shall be removed; Generally, the steel pipe surface does not need to be coated with oil after being cleaned, but for high-quality steel, alloy steel sheet, thin-walled pipe, alloy steel pipe, etc., the internal and external surfaces need to be coated with anti rust oil before storage; Steel pipes with serious corrosion shall not be kept for a long time after rust removal and shall be used as soon as possible. With the development of economy, all kinds of square tubes, rectangular tubes, seamless square tubes, galvanized square tubes and galvanized tubes have been recognized by the majority of customers for a long time. There are more and more counterfeit products on the market. In order to prevent being deceived when you are in square tubes, you need to know some knowledge about how to judge the authenticity of square tubes: & ldquo; We can judge by observing the surface and flatness of the square tube. If the surface of the square tube is relatively flat, it can reflect that the square tube is good. On the contrary, if the surface is not goodHow much does it cost?,The difference between hot-dip galvanized square pipe and cold-dip galvanized square pipe is mainly from the following aspects: the appearance of hot-dip galvanized square pipe is slightly rough compared with cold-dip galvanized square pipe; The appearance of cold galvanized square pipe is smooth and bright.Functional index analysis of square tube - angular plasticity refers to the power of plastic deformation (permanent deformation) without destruction of square tube data under load.The square tube for fluid transportation (gbt-) is a general square tube for transporting water, oil, gas and other fluids.Hard,If the test results of square tubes fail to meet the provisions of product standards, the unqualified ones shall be selected, and double the number of samples shall be taken from the same batch of square tubes for re inspection of unqualified items. If the re inspection results (including any index required by the test of the project) are unqualified, re inspection is not allowed: A. There are white spots in the low magnification; b. Microscopic.The local heat release in the welding process of square tube can reduce the heat affected zone, avoid the micro of thermal sensitive materials and maintain the properties of materials.Square tube production most square tube processing is square tube pressure processing, resulting in plastic deformation of the processed steel (billet, ingot, etc.). According to the square tube processing temperature, the square tube can be divided into cold processing and hot processing. The main processing of square tube includes: rolling: the gap (various shapes) between the square tube metal blank and the rotating roll , because of the compression of the roll, the material section is reduced and the length is increased. This is a common production method for producing square tubes. It is mainly used to produce square tube profiles, plates and tubes. It is divided into cold rolling and hot rolling.