SukhbaatorSubmersible non clogging slurry pumpHow to calculate the bearing capacity

　　If the pressure in the local area is equal to or lower than the vaporization pressure corresponding to the water temperature in the flow process, the water will vaporize there and form many small bubbles mixed by steam and gas. The cavitation phenomenon is due to the bubble action when these small bubbles flow from the low-pressure area to the high-pressure area in the water pump,　　 the water pipe shall be provided with a gate valve to regulate the pump working point. The valve shall be installed as close to the pump outlet as possible. The pump unit greater than meters shall be provided with a check valve at the pump outlet. In case of sudden shutdown, it is necessary to prevent damage to flow passage components caused by water hammer.Sukhbaator,　　 Long continuous operation time. Because the pump and motor are coaxial, the shaft is short, and the rotating parts are light, the radial load on the bearing is relatively small, and the service life of the submersible sewage pump is much longer than that of the general pump.　　Potential energy, pumping water up high. However, the equipment is shaped like a decoration, so what is the reason for this situation? How to solve it?Seraing,　　 When stopping the operation of the submersible slurry pump, close the cock of the vacuum gauge and pressure gauge and the gate valve on the water outlet pipeline, cut off the power supply of the motor. If the temperature of the environment is low,SukhbaatorSubmersible sewage pump, open the square plug at the lower part of the pump body to remove the remaining water to avoid frost cracking. During operation, the maximum temperature of the bearing shall not exceed ℃, and the quantity of calcium base grease used for lubricating oil bearing shall be the same as that of the bearing body　　There are differences.　　Pressure. Therefore, a pressure gauge should be installed in this system to monitor whether the pressure meets the requirements.

　　Other ysts believe that, at least in recent years, the situation of power shortage will continue, and China&#;s economic growth trend will maintain a high speed. Therefore, the contradiction between power supply and demand is still prominent in recent years which is undoubtedly an opportunity for it and the generator industry. In water pumps and generators, especially　　The actual operating flow is too large resulting in the following results: when the flow increases, while the efficiency of the motor remains unchanged, so the power of the input motor must increase. Excessive power makes the motor in an overloaded operation state, which may cause heating or even burn out the motor　　The structure of the submersible slurry pump will be more intuitive. First the equipment will use centrifugal force to drive the liquid from the impeller to the outer edge and obtain energy, and then leave the edge of the impeller at a higher speedQuality Assurance,　　The submersible slurry pump is a slurry pump which is connected with the motor and works under the water at the same time. Compared with horizontal slurry pump and vertical slurry pump, the biggest advantage is that it is flexible, convenient and easy to apply to various working conditions. The most important technical point of submersible slurry pump is the tightness between its motor and pump body Stability and reliability of seals.　　After the submersible slurry pump adds a water gun to the support at the bottom of the submersible slurry pump, the hardened mud layer around the slurry pump will collapse rapidly under the applied water pressure, which will also increase the sand pumping area. This will also increase the sand pumping area, so there will be no buried pump when it is used. However,　　In the mud pump, the axial force is mainly composed of the pressure difference force of the liquid effect on the impeller and the gravity of the whole rolling part. The effect direction of the two forces is the same, and the resultant force is the sum of the two forces. If the submersible slurry pump is equipped with an auxiliary impeller, the liquid effect is on the auxiliary impeller

　　 A trash trap can be added at the position of the water inlet pipe and used at an angle of degrees, and then a filter screen is installed in the trap to filter impurities for the second time, so as to avoid the blockage of the submersible slurry pump during use.Encyclopedic knowledge,　　A large amount of lubricating oil is stored.　　Conduct a comprehensive preventive maintenance once a year, including: replace all O-ring seals; Check the bearing wear and add new grease; Check the wear condition of the mechanical seal to determine whether it needs to be replaced; Check the wear of the impeller and the seal between the impeller and the pump body　　 It is also possible that the fan blades of the pump are few and the air volume is insufficient, resulting in poor heat dissipation effect.Sukhbaator,　　Promote the continuous expansion of the sales network group.　　The input quantity is related to many factors such as the rotating speed of the submersible slurry pump,SukhbaatorSubmersible pump can pump sewage, the bearing standard, the continuous working time, the number of stops and starts of the pump, the surrounding environment and the working temperature. Therefore, it is necessary to gradually accumulate the experience and add smooth oil in a reasonable and timely manner.　　No matter what type of slurry pump you need, Ritter pump will provide you with high-quality slurry pump products; New progress in submersible slurry pump technology in recent years The diving depth has increased from meters to meters!