TextCustomized hydraulic lifting platformThe price has risen year-on-year

There is noise inside the hydraulic cylinder. When replacing the hydraulic oil there was air in the hydraulic cylinder due to an operational error. Under high pressure, it is easy to generate cavitation and high-frequency noise. When the rod is bent or replaced with a new seal, the new seal is too tight, which can also produce significant noise. If it is a problem of tight sealing, the noise can be reduced after running in for a period of time. If the rod is bent, it needs to be corrected. In addition, hydraulic pipelines should use hoses as much as possible, even when arranging pipelines it can reduce vibration and noise, and the pipelines should avoid dead bends as much as possible.When using an electric mobile scissor lifting platform outdoors if the wind force exceeds level , please stop using it; When the lifting height exceeds meters, the wind ropes at the four corners of the hydraulic lift platform should be tightened and fixed, and the support legs should be reinforced for protection and stability to avoid safety accidents caused by excessive swinging of the electric lifting platformText,Hydraulic oil is the blood of the cargo elevator. Maintaining the cleanliness of hydraulic oil is an important factor in extending the hydraulic freight elevator. How to maintain the cleanliness of hydraulic elevators?The hydraulic lifting platform often checks the connection status of each part, it should be tightened. The connection bolts of the machine body should be checked for tightness when the elevator body is under pressure (the compression condition can be formed by rotating the arm). All connecting shafts need to have split pins and need to be fully opened.Pinhal Novo,If the circuit of the device is not disconnected or lowered, it is necessary to check the fuse for repair and replacement.The manufacturer of hydraulic cargo elevators reminds the use of guide rail hydraulic lifting cargo elevators. Guide rail hydraulic lifting cargo elevators: Do not stand within the specified range, draw on the guide rail lifting platform, prohibit any idle personnel from entering the work area, ensure that the work area is free of clothing, and maintain a clean and tidy workplace.The above are the working principles of three common elevators, and there are also some forms of elevators that are not common, such as cylinder mounted elevators, curved arm elevators, car mounted elevators, etc. Their common feature is the hydraulic principle for operation, because the stability of the hydraulic system can bring better user experience and safer operation to the equipment, which has been favored by many users.

The speed circuit is the circuit that switches the motion speed and speed of the actuator in the hydraulic system of the guide rail hydraulic lifting platform. Mainly including valves, pumps, and actuators. The commonly used speed circuits include speed circuits, high-speed circuits, and speed switching circuits.Many operating factories often require the use of hydraulic cargo elevators, which can be lifted and lowered, making it very convenient to use. Many people do not know the knowledge of hydraulic cargo elevator lifting and adjustment. If they understand this knowledge, it will be helpful for future maintenance. The power unit of the fixed chain elevator for hydraulic lifting of cargo elevators drives the hydraulic oil to generate pressure, causing the oil cylinder to move back and forth to drive the lifting platform, thus achieving the adjustment of lifting speed. The power unit adjustment, whether it is a scissor type lifting platform or a track type lifting platform, is composed of the power unit and the oil cylinder. The power unit is manufactured with four outlet holes, which can be adjusted in size to increase or decrease the hydraulic oil flow rate of the oil cylinder, Adjustable motor speed or electro-hydraulic proportional valve to adjust hydraulic oil flow rate; The longer the oil pipe and hydraulic oil pipe, the longer the rise time. So during installation, try to minimize the length of the pipeline within the allowable range of the design; On the basis of adjusting the power device, the size of the oil pipeline can also be adjusted, and corresponding adjustments can be made while ensuring that the equipment meets normal demand and safety.The vibration range is proportional to the lifting height. The higher the height, the larger the shaking range, especially for mobile hydraulic cargo elevators. When the working height exceeds meters, the wind ropes at the four corners of the hydraulic cargo elevator should be tightened to strengthen leg protection, increase stability, and reduce shaking.Design brand, and replace it if necessary.Considering the oil level in the oil tank it will cause leakage. Disassemble and clean the check valve, when all hydraulic cylinders in the system are extended, the oil level in the oil tank should not be lower than the Z-low oil level, the oil level should not be higher than the Z-high oil level. In fact, most manufacturers have noticed the above issues. The reason for the introduction is that most users can learn more about the equipment itself when using elevators, in order to facilitate equipment maintenance. Hydraulic cargo elevator manufacturers sincerely hope that you choose a legitimate manufacturer when purchasing elevators, to avoid any worries about after-sales service.Each box, distribution box,TextImported hydraulic lifting platform, etc. should be kept clean and promptly cleaned of dust on electrical equipment.

The optional configurations of a fixed lifting platform include manual hydraulic power, movable flip plates that are easy to overlap with surrounding facilities,TextProduction hydraulic lifting platform, rolling or motorized roller tracks, safety contact bars to prevent foot rolling, organ type safety protective covers, manual or motorized rotating workbenches, hydraulic overturning workbenches, safety support rods to prevent the lifting platform from falling, stainless steel safety nets, and universal ball countertops.retailerMaterials enter the production line at one end of the factory building, and the production process ends at the other end of the factory building with multiple separate platforms; This can greatly shorten the distance of material flow in the factory building.Today, we will share with you why hydraulic cargo elevators are ideal equipment for transporting goods?New reference wiring diagram . Elevator leg noise. Mobile elevators should open the legs before operation. In this case, if the legs lack butter,When placing materials on the platform, they should be placed in the middle of the platform as much as possible. The weight of the goods should be within the standard load range of the equipment, and the volume of the goods should not exceed the platform size of the equipment. Otherwise, materials and lifting platforms may be injured and dangerous accidents may occur. High priced and various specifications of elevator manufacturers provide timely supply, with high cost-effectiveness, and have become the preferred brand for many wire products. Welcome to purchase!The hydraulic lifting platform is a manually movable type, and the lifting power of the platform is a two machine or three-phase power supply. It has manual and electric power, and is also equipped with a hand pump for use in case of power outage. This series of platforms have the characteristics of flexible movement, stable lifting, and easy operation, and are mainly used in factories, government agencies, commercial stores, and the construction and decoration industry.The undercut length of the weld mm should not exceed % of the weld seam, and the depth should not exceed .mm.