MesaISG single stage vertical pipeline pumpThe manufacturer shall pay attention to its maintenance

　　Work no noise and vibration, and the site is cleaner.　　 In addition, the use of ° and S-shaped bends should be reduced as much as possible during the installation and design of pipelines.Mesa,　　The equipment of this series of sewage pumps can be fixed or mobile. When the fixed active equipment is selected,MesaISG single stage vertical pipeline pump, the chain cable shall be separately threaded into (against the pump outlet, and its connection shall be parallel to the pump outlet) two eyebolts or lifting plates to lift the electric pump up and down. Evenly and slowly along the guide rail　　Therefore, the correct selection of shaft seal can ensure the safe and stable operation of slurry pump.Siraha,　　No matter what type of slurry pump you need, Ritter pump will provide you with the highest quality slurry pump products; The latest development of submersible slurry pump technology in recent years The diving depth has increased from meters to meters!　　Then it can enter into the volute pump housing. Then in the volute pump casing, the medium slows down because the flow channel is also gradually expanding.　　Cavitation of the pump is caused by water evaporation of the pump. The main cause of water evaporation is related to temperature and pressure. Under a certain pressure, when the temperature rises to a certain value, the water begins to vaporize and change from liquid to gas. On the contrary, at a certain temperature, the pressure drops to

　　Water pump is a kind of machinery that pumps energy liquid. It is a machine that converts the mechanical energy of the prime mover into the potential energy of the pumped liquid. Driven by power machinery, it can pump liquid from low to high or far away to serve production.　　Self priming refers to the process of sucking water from low to the pump cavity when there is no water (empty pipe) in the inlet pipeline (verb, self priming is an action and a process). Only the self-priming pump can have the self-priming .　　Reasonable.Good quality,MesaVortex pump and pipeline pump,　　The development of submersible slurry pump is to adapt to increasingly complex working conditions, facilitate users to use, and its use mode is more flexible. And it fills a part of the gap in the application of slurry pump. When the submergence depth is deep and there is no better slurry outlet, that is, in the traditional slurry pump　　When the water level reaches, the frequency of the frequency converter drops, and the slurry pump operates at a low speed. The higher the water level, the lower the speed; The lower the water level,MesaUsed pipeline pump, the higher the speed. At the same time, which are padded with green paper or asbestos. There is a gap of .- mm between the rear gland and the bearing.

　　The slurry pump of underground pump can also work normally.Inspection basis the circulation in the slag slurry pool is basically unchanged　　 the front and rear bearing glands are equipped with oil seals,　　Generally speaking, the above two cases are the case that the slurry pump does not absorb water. The solutions are also introduced. I believe that people can deal with this problem in time. However, if the problem is serious, you must not adjust it at will. At this time, you should find a professional　　Check the three-phase current with an ammeter on the control panel. If the phase power supply is found to be insufficient, connection point and power switch contact are in poor contact and whether they are the main line. Check whether the circuit wiring is broken or loose, or whether the fuse is damaged or burnt out　　The purpose is to avoid water leakage of the pump,　　With the continuous development of slurry pump technology, submersible slurry pump appears in response to market demand. It is especially suitable for the depth at which the vertical slurry pump cannot operate. The underwater part of the vertical slurry pump is generally not more than m, and of course it can be more than. For example, the maximum design depth of our company&#;s underwater slurry pump can reach m, but such underwater depth is not the best operating depth of this kind of pump, so it will lead to the unreliability of the operation of the vertical slurry pump from time to time.　　 install a valve to inject water at the water inlet and outlet. This method is to install a valve on the water inlet pipe of the submersible slurry pump and connect the water pipe to inject water into the pump. This is a common and simple method.　　Rotate in the rolling direction until the friction between the impeller and the front guard plate stops, then use the adjusting bolt to move the rotor backward, record the forward and backward movement gap, evenly distribute it between the front and rear guard plates of the impeller until the gap between the impeller, the front guard plate and the rear guard plate is flat stop, and tighten the two dust discs and fasten them on the shaft. adjustment