Bai LinggenSingle suction slurry pumpPrinciple of deformation process

　　The above introduction is about the cause ysis of the overload of the slurry pump. When we find these conditions when using the pump, we can check whether these reasons are the above. This is also a reminder that we need to maintain the pump during normal use. latent　　Let the medium containing some solid particles generate a certain flow rate, so that the equipment can drive the solid to flow when it is in use, so that the slurry can be transported. In terms of the principle of the submersible slurry pump, it is actually quite simpleBai Linggen,　　During daily use, we can observe, so as to judge whether there is a fault and the fault part of the slurry pump, and deal with it in time if any fault is found.　　Will be scrapped. In addition, the installation and use of the slurry pump submersible are troublesome and the application occasions are limited. The submersible slurry pump is developed to adapt to increasingly complex working conditions and facilitate the use of users. Its use mode is moreFria　　The above is the correct sequence of impeller disassembly of submersible slurry pump. Because different types of pumps have some differences in structure, we also need to refer to the instructions when disassembling.　　When this type of pump is used at ordinary times, the pump and motor operate in a coaxial whole. When it runs,Bai LinggenCirculating hot water pipeline pump, the motor shaft will drive the impeller of the pump to rotate, and then at this time, the rotating force can be brought to the medium, so that　　 A trash trap can be added at the position of the water inlet pipe and used at an angle of degrees, and then a filter screen is installed in the trap to filter impurities for the second time so as to avoid the blockage of the submersible slurry pump during use.

　　 First of all,Bai LinggenBooster pipeline pump, we need to know that submersible pumps generally operate in water. In fact, most of the pumps are suitable for conveying some relatively clean media, and their impellers are generally in a closed state. However, one of the media conveyed by sewage pumps may　　I believe you have such a question when using the submersible sewage pump, that is, is this pump a submersible pump? Or is it a sewage pump? In fact, this question is very easy to distinguish. You can take a look at the following contents sorted out by Shanghai Shenquan.　　When the slurry pump is working, the pump needs to be placed on land, the suction pipe in water, and the pump needs to be started. Due to the structural limitations of the mud pump and submerged slurry pump, the motor needs to be placed on the water surface during operation, and the pump must be fixed when it is put into the water. Otherwise, the motor will fall into the waterPursuit of excellence,　　For example, it has a great impact on the impeller of the equipment itself. So how to detect whether the equipment has cavitation during use?　　 Pipeline layout: Firmly support the water pipe and drain pipe to prevent the force of the pipe from acting on the submersible slurry pump.　　Circumference. In the application of slurry pump,Bai LinggenQuotation slurry pump, we must pay attention to reasonable design, correct calculation and appropriate type selection, a set of stirring impeller is added at the bottom of the product, which can spray the precipitated slag into a mixture of water and solid particles

　　 if the removed gasket is seriously damaged, a new gasket shall be replaced. The removed parts shall be cleaned with kerosene before assembly.Quality improvement,　　 Then tighten the compression nut on the packing gland evenly to make the liquid leak out in drops, and pay attention to the temperature rise outside the packing chamber.　　 discharge requirements for water leakage of pump seat packing　　Moreover, because the length of the long shaft is generally fixed it is often troublesome to install it. Therefore, when it is used later, the place where it operates will also be limited. If the equipment willBai Linggen,　　After that, the secondary and tertiary pumps can be started successively until the final stage pump. After all the series pumps are started, the outlet valve of the final stage pump can be gradually opened. The speed of opening the valve should be controlled by the fact that the pump does not vibrate and the motor of any stage does not exceed the rated current.　　In addition, the sundries inside the pump body and impeller shall be cleaned. Then calibrate the pump shaft and motor shaft of the slurry pump to make them on the same horizontal line.　　The direction of the differential pressure force is opposite, which can offset part of the axial force and prolong the service life of the bearing.