TurkwanInstallation price of fresh-keeping cold storageExplanation of purchasing methods

Install the library body. Generally, compact and solid, without hollow feeling, load-bearing, antifreeze, moisture-proof, etc.For cold storage, but its energy consumption is very large in the use of cold storage. How can we solve this problem?Turkwan, foam, and then evenly coated in the area to be leaked and observe for a few minutes. If water leaks, bubbles will appear. Mark the leaking area, and then tighten or gas cut it.Watertight polyurethane rigid foam has low water absorption, good permeability to water vapor, and state of foam pores. It is not connected with each other,TurkwanWhere is it cold, and the obturator rate is more than %. It is a dense microporous foam material, which is more dense than the surface of the air, and is not easy to permeate. It is an hydrophobic material.Queenstown,Other aspects: in the design process of food cold storage, it is also necessary to consider the cooperation between the cold storage and on-site fire fighting, ventilation, water and electricity systems. It should meet the requirements of safety, science and environmental protection. When designing and installing the cold storage, the drainage problem must be considered, and the following points should be paid attention to during redesign and installation.Goods are imported and exported frequently and the throughput is large according to the requirements of production and operationThe type of cold storage to be built in the type of cold storage should be determined according to the type of circulating goods. For example, while the cold storage with refrigeration + freezing will be built if there are many types of circulating goods and great difference in storage temperature. As for the size of the cold storage, it should be determined according to the type, quantity, frequency cycle, whether to use shelf stacking and so on. For example, for fruits and vegetables packed in cartons, the storage capacity of -kg per cubic meter can be referred to, and the size of cold storage construction can be estimated in combination with the storage capacity rate of about .-..

There are two kinds of refrigeration in the cold storage group: immediate refrigeration and simple refrigeration.Clean the bearing and replace the oil in the centrifugal pump, and the vibration of the shaft.Initial stage of cold storage equipmentQuotation sheet,Some cold bridge prevention measures shall be taken at the joints between polyurethane insulation boards.The refrigerant charge is insufficient. At this time, just add enough refrigerant.The temperature and humidity in the warehouse shall be kept uniform without movement; Try to finish the food in the warehouse at one time.

The exhaust temperature of the compressor equipment is often. When the season changes and the temperature difference changes greatly, pay attention to it. If the machine is abnormal, it needs to be checked in time.The cheapest,The polyurethane insulation board used in the construction of cold storage shall be integral and continuous, and there shall be no joint in the middle. The junction of polyurethane insulation board, top plate and ground shall be made into fillet arc for transition,TurkwanTea cold storage, which can well meet the health needs.When adjusting the station, each outlet pipe shall be sawn into a degree inclined mouth to the bottom, and the inlet pipe shall be points of the pipe diameter of the adjusting station.The drainage at the outlet of the cooling fan, the drainage of the volatile cooler and the road drainage of the refrigerated warehouse storing food or drinks shall not be immediately connected with the sewage and wastewater pipeline system software, but indirect drainage shall be adopted. For the flushing (thawing) water drainage of each layer in the double-layer cold storage,TurkwanInstallation and construction price of cold storage, an exhaust valve equipment shall be set in front of the main riser for flushing (thawing) water drainage.Turkwan,Compression refrigerator is commonly used. It is mainly composed of compressor, condenser throttle valve and evaporation pipe. The evaporation pipe is installed in the refrigeration warehouse. When the liquid coolant passes through the evaporation pipe, it directly absorbs the heat in the warehouse and cools down.Generally, in the actual operation of the refrigeration system, because the temperature conditions are constantly changing, only by relying on the careful operation of the cold storage management personnel and accurately adjusting the operation of the refrigeration equipment of the cold storage, can the refrigeration system always be in the ideal working state and achieve the effect of energy saving.In order to prevent damage to the cold storage, it is necessary to lay some foam on the floor of the cold storage tank.